Dometic RM7030 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 38

background image

20

DOMETIC® RM7030/RM7732

Refrigerators

DIAGNOSTIC SERVICE MANUAL

7.2

ORIFICE

The orifice is a small brass fitting that has a ruby

membrane that is laserbeam drilled and is mounted on

the gas line just prior to the burner. The orifice is

cleaned by using an alcohol based solvent and allowing

to air dry.

NEVER USE A DRILL BIT OR JET TIP CLEANER TO

CLEAN ANY ORIFICE AS THESE DEVICES WILL

DAMAGE THE FACTORY MACHINED PART AND

CREATE A POTENTIALLY DANGEROUS CONDI-

TION.

If there is lack of cooling on gas operation, verify the

orifice is the proper size (#73).

7.3

THERMOCOUPLE

A. RM7030 (Product No. 921890201 & 921890301)

The thermocouple is a component extending above the

burner assembly so the tip is in the path of the flame. It

will produce 14 to 30 millivolts DC in normal operation.

To check the thermocouple, use a known good safety

valve and attach to the thermocouple. Next, supply

flame to tip of the thermocouple for a few moments

while depressing the safety valve. Remove the flame

and release the safety valve.
The valve should hold for at least 30 seconds. If it does

not hold the safety valve open for 30 seconds, replace

the thermocouple. If it does hold for 30 seconds or

more, the thermocouple is good do not replace it.

NOTE: Be sure the tip on the thermocouple is clean.

B. RM7030 (Product No. 921890401) & RM7732

The thermocouple is a component extending above the

burner assembly so the tip is in the path of the flame.

During normal gas operation, the thermocouple should

produce 25 to 35 millivolts when connected to the lower

circuit board. Any reading below 18 millivolts could

cause erratic gas operation.

NOTE

: A reading of 18 or

less could be caused by low gas pressure or improper

thermocouple location.

RM7030 (Product No. 921890401) and RM7732

PRESSURE TEST

PORT

ORIFICE

THERMOCOUPLE

ELECTRODE

BURNER TUBE

RM7030 (Product No. 921890201 & 921890301)

All manuals and user guides at all-guides.com

«
...
21
22
23
24
25
...
»

Содержание RM7030







































Отзывы:

Нет отзывов

Похожие инструкции для RM7030

Cafe CYE23TSDSS

Бренд: GE Страницы: 2

Бренд: Haier Страницы: 34

Бренд: EAS Electric Страницы: 107

Бренд: EAS Electric Страницы: 120

Бренд: Jenn-Air Страницы: 23

Бренд: Blaupunkt Страницы: 4

Бренд: Blomberg Страницы: 48

Бренд: Maytag Страницы: 1

ACTIVESMART RF203Q

Бренд: Fisher & Paykel Страницы: 44

Бренд: elvita Страницы: 116

Бренд: iGenix Страницы: 13

Бренд: Engel Страницы: 1

Refrigerator/freezer

Бренд: Tricity Bendix Страницы: 16

FRN-U20IA Series

Бренд: Daewoo Страницы: 24

Бренд: NABO Страницы: 39

Бренд: Cylinda Страницы: 116

Бренд: Smeg Страницы: 11

Бренд: U-Line Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды