Dometic RM7030 Скачать руководство пользователя страница 13

Страница: 13 / 38

DOMETIC® RM7030/RM7732

Refrigerators

DIAGNOSTIC SERVICE MANUAL

5.2

THERMISTOR

RM7030 (Prod. No. 921890401) and RM7732

To determine if the temperature sensor is functioning

properly, perform the following test.
Remove the cover from the lower circuit board. Discon-

nect the thermistor harness from the P2, 2-pin terminal

on the lower circuit board. Place thermistor in a glass of

ice water. Wait 2 to 3 minutes. Using an ohm meter,

place a probe on each terminal point. You should get a

reading of approximately 7,000 to 10,000 ohms. Normal

failure for this type of device is to have a very high

resistance. A defective thermistor could cause an over-

cooling condition on all modes.

5.3

THERMISTOR ADJUSTER

RM7030 (Product No. 921890401) and RM7732

The thermistor adjuster is a resistor-type component

that attaches between the thermistor and the lower

board. Its function is to allow the refrigerator to reach

temperatures below the normal 46° to 35°F. range

(setting 1 through 5 on upper circuit board).
To determine if the thermistor adjuster is operating

properly, do an ohms resistance check across the

terminals. Proper ohms reading is approximately 23,200

ohms ± 10%.

5.4

SOLENOID VALVE

A. RM7030 (Product No. 921890201 & 921890301)

The solenoid valve assembly is a safety valve as well as

a gas flow valve. When the AES selects LP gas opera-

tion, DC volts are sent to the solenoid coil which opens

the internal valve.
Check the solenoid coil with a properly

calibrated ohm meter. Remove the

connector from the solenoid

and measure the resis-

tance across the upper

and lower terminals. The

proper reading would be

20 ohms with a toler-

ance range of ten

percent. Once flame is

lit, the thermocouple

produces the voltage to keep

the valve open. If for any reason the thermocouple does

not provide enough current to the valve, it will close,

stopping the flow of gas. To check this portion of the

solenoid valve assembly, verify the thermocouple is

good (see Sec. 7.3A), the tip is clean and the receptacle

in the solenoid valve assembly is clean. If the thermo-

couple checks good, then replace the solenoid valve

assembly.

NOTE

: If the solenoid ohms check shows an open coil,

the refrigerator will not operate on any mode.

THERMISTOR
ADJUSTER

TO THERMISTOR

NOTE

: Dometic refrigerators do not come equipped with a

thermistor adjuster. This is an add-on component.

THERMISTOR

ADJUSTER

TO THERMISTOR

B. RM7030 (Product No. 921890401) and RM7732

When the refrigerator selects LP gas operation, DC

volts are sent to the solenoid coil which opens the

internal valve.

Check the solenoid coil with a properly calibrated ohm

meter. Remove the connector from the solenoid and

measure the resistance across the terminals. The

proper reading would be 49 ohms with a tolerance

range of ten percent.

Thermistor
unplugged
from PC
Board

All manuals and user guides at all-guides.com

Содержание RM7030







































Результаты поиска

Содержание RM7030

Отзывы:

Похожие инструкции для RM7030

Бренды по названию

Популярные бренды

Dometic RM7030, Руководство по обслуживанию

Результаты поиска

Содержание RM7030

Отзывы:

Похожие инструкции для RM7030

Бренды по названию

Популярные бренды