background image

Section III - Coverage Period

 

 DuraSea Rooftop Installation & Operations Manual

16

L-3075 ENGLISH

13. UV light bulbs are not covered.

14. Liquid line filter dryers are not covered.

15. Blowers with water damage.

16. Logic boards with water damage.

17. Logic boards with blown MOV's (Power Surge)

18. Mis-programmed displays.

19. Display heads with water damage.

20. Dirty Condensers and/or Evaporators.

21. Failures due to improper winterization.

22. Unit damage as a result of improper return packaging.

23. Replacement of freon with substitute without authorization from factory.

24. Environmental and/or Recovery Fees.

25. Welding and Nitrogen Fees.

26. Travel costs are included in the hourly labor allowances and should not be billed as a separate item without 

preapproval form the factory.

Installation and application of Dometic components is not warranted by Dometic, because Dometic has no control or 
authority over the selection, location, application, or installation of these components.

S

ECTION

 III - C

OVERAGE

 P

ERIOD

What is the period of coverage?

(See 

Limited

 

Warranty Periods 

at the end of this book).

All Dometic components bear a data plate on which there are model and serial numbers. The serial number is date coded. To 
determine whether or not any Dometic component is in warranty, proceed as follows:

1.

Determine the manufacture date of the component from the serial number on the data plate. If you are not familiar with 
the date code, write or call the Dometic Customer Service Department to obtain the manufacture date. The hours of 
the Customer Service Department are 8:00 a.m. - 5:00 p.m. (USA, Eastern Standard Time Zone) Monday through 
Friday excluding holidays.

2.

It is possible that there might exist a considerable time lag between the date a component is manufactured and the 
date it is put in service. In such instances, the date of manufacture could indicate that the item is out of warranty. 
However, based on the date the equipment is first put in service, the item may still be covered by the Dometic warranty 
as described in 

Section I

. For proof of date put in service, Dometic will require a copy of the bill of sale of the Dometic 

equipment from the installer or new boat dealer to the original owner. 

S

ECTION

 IV - G

ETTING

 S

ERVICE

How do you get service? 

Please read the following Warranty Procedure:

If the failure of a Dometic component is determined to be covered under the Dometic warranty and the time in service is 
determined to be within the warranty time limit, the owner has the following three options: 

1.

Preferred option: Have a Dometic authorized Servicing Dealer, perform the work needed. The customer needs to call 
Dometic Customer Service Department for a recommendation as to the closest dealer. If the customer already knows 
an authorized servicing dealer, the dealer should be contacted directly.

2.

Second option: If the customer contacts Dometic Service Department for a Servicing Dealer and Dometic has no one 
in that particular area, Dometic will authorize the use of a local service company and Dometic will work with the local 
company to assist in any way possible.

3.

Third option: The customer may send his equipment back to the factory to have the repair work done. Dometic will 
make every effort to return the equipment to the customer within a three week time period. If the claim represents a 
legitimate warranty problem, Dometic will pay the freight both ways. Dometic prefers option one first, option two 
second, and option three only if one and two are not available.

The customer may contact the Dometic Service Department at 954-973-2477 Monday through Friday, 8:00am - 5:00pm Eastern 
Time. After hours (evenings and weekends) technical support is offered through Dometic's 24/7 Hotline at 888-440-4494.  

Содержание DuraSea





















Отзывы: