Dodge 2016 Viper SRT ACR Скачать руководство пользователя страница 256 | Manualshive

Страница: 256 / 427

background image

NOTE:

If the cluster launch DID message indicates all

conditions are correct for launch and the throttle is
pressed to the floor quickly (within approximately 1/2
second) the system will hold the engine speed to a preset
speed (below the engine rev limiter speed).

6. Release the clutch aggressively. Do not ride the clutch.

Release the accelerator pedal to deactivate launch con-
trol. Pushing the launch control button or actuating the
brakes will also deactivate launch control.

NOTE:

•

Launch Mode brings the engine to optimum launch
RPM and waits for the driver to release the clutch.
Launch Mode then uses engine throttle only to achieve
controlled wheelslip for maximum acceleration
through first gear.

•

Launch Mode can be used in any of the Electronic
Stability Control (ESC) Modes.

•

Launch Mode should not be used within the first
500 miles (805 km) of engine break-in.

WARNING!

Launch Mode is intended for off-highway or off-road
use only and should not be used on any public
roadways. It is recommended that this feature be
used in a controlled environment, and within the
limits of the law. The capabilities of the vehicle as
measured by the performance pages must never be
exploited in a reckless or dangerous manner, which
can jeopardize the user’s safety or the safety of
others. Only a safe, attentive, and skillful driver can
prevent accidents.

254

STARTING AND OPERATING

«
...
254
255
256
257
258
...
»

Содержание 2016 Viper SRT ACR












































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2016 Viper SRT ACR

Бренд: JETBAG Страницы: 44

Бренд: Harbor Freight Tools Страницы: 4

RadioPRO 5 RP5-GM41

Бренд: PAC Страницы: 3

Бренд: Yakima Страницы: 8

Бренд: GATmatic Страницы: 13

Porsche 911 GT3 R

Бренд: iRacing Страницы: 25

Бренд: Mazda Страницы: 13

Бренд: PAC Страницы: 4

PRIME DESIGN VRR-E-PM21

Бренд: Safe Fleet Страницы: 12

Бренд: Flash Cover Страницы: 2

Бренд: Tachosys Страницы: 28

Impala Limited 2014

Бренд: Chevrolet Страницы: 356

Бренд: Kia Страницы: 51

Бренд: ACV Страницы: 2

Бренд: Yakima Страницы: 13

Бренд: Linear Logic Страницы: 8

2010 MX-5 Miata

Бренд: Mazda Страницы: 8

RAV-4 2015 Series

Бренд: Toyota Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды