Dodge 2016 Viper SRT ACR Скачать руководство пользователя страница 107

Страница: 107 / 427

2. Pull the hood release lever rearward to release the

hood latches.

3. Lift the hood upward to the full forward position.

NOTE:

The recommended lift point is to place the lifting

hand forward of one of the wiper arms and pull up. The
assist props will help raise and hold the hood to a normal
usage position.

Hood Release Lever

Opened Hood

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

105

Содержание 2016 Viper SRT ACR












































































































































































































































































































































































































































Результаты поиска

Содержание 2016 Viper SRT ACR

Отзывы:

Похожие инструкции для 2016 Viper SRT ACR

Бренды по названию

Популярные бренды

Dodge 2016 Viper SRT ACR, Руководство пользователя

Результаты поиска

Содержание 2016 Viper SRT ACR

Отзывы:

Похожие инструкции для 2016 Viper SRT ACR

Бренды по названию

Популярные бренды