Dodge 2016 Viper SRT ACR Скачать руководство пользователя страница 364 | Manualshive

Страница: 364 / 427

background image

WARNING!

(Continued)

•

Do not allow petroleum based fluid to contaminate
the brake fluid. Brake seal components could be
damaged, causing partial or complete brake failure.
This could result in an accident.

Change Brake Fluid

Brake fluid will tend to absorb moisture from the atmo-
sphere over time. If the fluid becomes contaminated with
water, brake performance will deteriorate. Therefore, the
brake fluid must be changed at the intervals specified in
the “Maintenance Schedule.” Refer to “Maintenance
Schedule” for further information. See your authorized
dealer for service.

Manual Transmission

Transmission Fluid Level Check

Check the fluid in the transmission when performing
other underbody services.

Check the fluid level by removing the fill plug located on
the left side of the transmission. The fluid level should be
approximately 1/4 in (6.4 mm) below the bottom of the
fill hole. Add fluid, if necessary, to maintain the proper
level. Refer to “Fluids, Lubricants, And Genuine Parts” in
“Maintaining Your Vehicle” for further information.

NOTE: DO NOT

overfill transmission, damage can

occur.

362

MAINTAINING YOUR VEHICLE

«
...
362
363
364
365
366
...
»

Содержание 2016 Viper SRT ACR












































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2016 Viper SRT ACR

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Бренд: hc-cargo Страницы: 60

Бренд: Kuda Страницы: 3

Бренд: U.S. General Страницы: 8

Бренд: Abrams Страницы: 12

Бренд: BMW Страницы: 392

Бренд: Curt Manufacturing Страницы: 4

Бренд: Saab Страницы: 9

Бренд: true-i Страницы: 11

Telescoping Computer Base C-TCB-34

Бренд: Havis-Shields Страницы: 1

Бренд: PEUGEOT Страницы: 107

Charger SRT 392 2017

Бренд: Dodge Страницы: 576

Бренд: Lexus Страницы: 108

Бренд: iSimple Страницы: 8

Turbocharger 15012

Бренд: Edelbrock Страницы: 1

Yukon XL Denali 2015

Бренд: GMC Страницы: 439

Бренд: Phonocar Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды