background image

 

AFE8B

 

 

 

 

BATTERY POWERED CRIMP TOOL

 

 

DATASHEET 

 

________________________________________________________________________________________________ 

AFE8B-DS 

©2012 Daniels Manufacturing Corp., All Rights Reserved              Page 5 of 7 

REV. D 

 

6/20/2014 

 
 

                                                 Daniels Manufacturing Corporation 

 

                                                 526 Thorpe Road, Orlando, FL 32824 USA 

 

                                              Phone: 407-855-6161 Fax: 407-855-6884 Email: [email protected] 

Maintenance 

 
Each Operating Day 

Before Use: 

1.

 

Inspect indenters for wear or damage such as 
cracks, gouges, or chips. 

2.

 

Inspect the tool for damage or leaks.  If damage is 
detected, return the tool to the DMC repair center 
for inspection. 

After Use: 

1.

 

Wipe all tool surfaces clean with a damp cloth and 

mild detergent. 

2.

 

Charge the battery. 

3.

 

Fully retract the tool push rod. 

4.

 

Place the tool in the carrying case. 

5.

 

Store in a cool dry place. 

 
Monthly 

1.

 

Thoroughly clean all surfaces. 

 

Trouble Shooting 

Before You Begin 

1.

 

Make sure that the battery is charged.  Recheck the 

battery after several minutes to make sure the 
battery is holding its charge. 

2.

 

Use a nonflammable contact cleaner or pencil eraser 

to clean the electrical contacts on the battery and 
crimp tool. 

3.

 

Reinstall the battery and check the tool again. 

 

Problem   

Probable Cause 

 

Probable Remedy 

Tool is inoperative  Dirt, contaminants, etc, 

Clean tool. 

 

 

in ram area of tool. 

 

 

 

Crimping tool battery 

Reform contacts. 

 

 

contacts damaged. 

 
 

 

Tool components worn or 

Return tool to DMC. 

 

 

damaged. 

 

Dies stop during 

Oil level is low. 

 

Return tool to DMC. 

operation. 

 
 

 

Air in hydraulic system. 

Press trigger and hold 

 

 

 

 

 

emergency release 

 

 

 

 

 

button simultaneously. 

 

 

 

 

 

Hold for approximately 

 

 

 

 

 

10 seconds. 

 

Tool loses oil. 

Damaged internal seal. 

Return tool to DMC. 

 

Gaging the crimp tool 

 

The crimp should be gaged periodically to ensure that 
proper crimping is being performed.  Intervals between 

checks should be determined by the customer based on tool 
use and environment the tool is used in.  Gaging is checked 

by crimping soft solder and measuring the indents created 
with a point to point gage. 
 

Gaging Instructions 

1.

 

Insert a short length of soft solder into the crimp 
area of the tool.  1/16” diameter for settings 1 thru 
4, & 1/8” diameter for settings 5 thru 8. 

2.

 

Activate tool to crimp the soft solder. 

3.

 

After crimping, measure the depth of two of the 
opposing indents with a point to point gage as 

shown. 

                       

 

4.

 

Measurements should be as follows: 

                   

 

 
Battery Charger Operating Instructions 

 
Operating Environment 

The charger is designed for use in dry areas.  All ventilation 

slots must be kept free.  If possible, keep away from heat 
sources and out of direct sunlight as ambient temperatures 

in excess of 95°F (35°C) may increase charging times 
significantly. 
 

AC Connection 

Before connecting the charger, check that the AC supply 

voltage is the same as what is indicated on the charger. 
 

 
 

Содержание AFE8B








Отзывы: