DKS 1812 Classic, Инструкция по установке и эксплуатации

Страница: 29 / 46

1812-065-V-12-14 27
2.4.3 Automatic Relay Activation Time Zones Programming
This program sequence sets up time zones to automatically activate and deactivate the relays on the control board. Each
relay can be programmed with two independent time zones. Time zones 1 and 2 affect relay 1 operation; time zones 3 and 4
affect relay 2 operation. These time zones MUST still be independently enabled or disabled after they have programmed
(See 4.9).
1. Press
*
3 5 and enter the MASTER CODE. [
*
3 5 _ _ _ _ (beep)]
2. Enter a time zone number (1 or 2 for relay 1, 3 or 4 for relay 2), then press
*
. [ _
*
(beep)]
3. Press 0
*
to turn time zone OFF, OR press 1
*
to turn time zone ON. [ _
*
(beep)]
4. Enter the beginning hour (01 to 12) and minutes (01 to 59), then press 0
*
for AM OR
press 1
*
for PM. [ _ _ _ _ then _
*
(beep)]
5. Enter the ending hour (01 to 12) and minutes (01 to 59), then press 0
*
for AM OR
press 1
*
for PM. [ _ _ _ _ then _
*
(beep)]
6. Enter the days of the week that a relay time zone is to be active, then press
*
.
[ _ _ _ _ _ _ _
*
(beep)]
Sun =1, Mon = 2, Tue = 3, Wed = 4, Thu = 5, Fri = 6, Sat = 7.
Note: All 7 programming spaces must be populated. After all the desired day numbers have been entered,
enter # in all the existing unused spaces.
For example, for a relay to be active monday through friday only, enter 2 3 4 5 6 # #
*
.
7. Repeat steps 2 through 6 to program the other time zones (up to 4).
8. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
2.4.4 Access Code Time Zone Programming
This programming sequence sets up a time zone for ALL four-digit access codes that have been programmed into the time
zoned access code location areas. Access codes that are programmed into these location areas will not work outside of the
programmed time zone. This time zone MUST still be enabled or disabled once it is programmed (See 4.8). See 2.6.1 to
program access codes.
1. Press
*
3 6 and enter the MASTER CODE. [
*
3 6 _ _ _ _ (beep)]
2. Press 0
*
to turn time zone OFF, OR press 1
*
to turn time zone ON. [ _
*
(beep)]
3. Enter the beginning hour (01 to 12) and minutes (01 to 59), then press 0
*
for AM OR
press 1
*
for PM. [ _ _ _ _ then _
*
(beep)]
4. Enter the ending hour (01 to 12) and minutes (01 to 59), then press 0
*
for AM OR
press 1
*
for PM. [ _ _ _ _ then _
*
(beep)]
5. Enter the days of the week that the access code time zone is to be active, then press
*
.
[ _ _ _ _ _ _ _
*
(beep)]
Sun =1, Mon = 2, Tue = 3, Wed = 4, Thu = 5, Fri = 6, Sat = 7.
Note: All 7 programming spaces must be populated. After all the desired day numbers have been entered,
enter # in all the existing unused spaces.
For example, for the access codes to be active monday through friday only, enter 2 3 4 5 6 # #
*
.
6. Press 0 # TOGETHER to end. [0 # (beeeeeep)]