background image

 

OPERATION INSTRUCTIONS

 

The safe and successful operation of the Model 560 will depend upon the operator having the 

correct knowledge of all controls used on the mower and making good judgements about the 

terrain to be mowed. 

NEVER 

allow anyone to operate the mower without complete knowledge 

of all controls and their functions.

 

Sound judgement by the owner will prevent accidents. All 

controls are described from operators position:

 

PARKING BRAKE:

 

The parking brake used on the Model 560 is designed to hold the mower from 

moving and is not intended for use in stopping the mower while it is in motion. 

An additional safety feature of the parking brake is that the engine cannot be 

started unless the brake is applied.

 

HYDROSTATIC DRIVE SYSTEM:

 

Allows the mower to turn on its own axis (zero radius). Each lever controls one 

side of the mower. The pressure required to operate the mower is very light and 

a minimum of 1

12 

hour should be spent simply driving the mower in a non-mowing 

application to gain the confidence neccessary to mow like a pro.

 

LEVER MOVEMENTS:

 

No shifting or clutching required. 

TO GO FORWARD:

 

Release parking brake. From neutral position, gently push both drive levers 

forward; to increase speed, move levers farther forward.

 

TO GO BACKWARD:

 

From neutral position, gently pull both drive levers toward you.

 

TURNING:

 

Turning is controlled by moving one drive lever slightly forward or rearward of the 

other. To turn left, move left lever rearward of the right lever. To turn "square 

corners" move lever of desired direction to neutral. To turn on mower's own axis 

(zero radius) reduce speed and move one lever to reverse position and the other 

to forward position.

 

 

Page 13

 

Содержание ZTR 560











































Отзывы: