Dixie Narco DN552P-7 Скачать руководство пользователя | Manualshive

Страница: 6 / 76

background image

INSTALLATION & SETUP

P-SERIES

Page 6 of 76

SPACE THE VENDER

Do not block the rear of the vender. Keep the vender 4
inches (10 cm) from the wall to ensure adequate airflow to
the condenser and compressor. At the front of the vender,
make sure that nothing obstructs the air intake at the
bottom of the main door. At the rear of the vender, make
sure nothing obstructs the air exhaust at the bottom of the
cabinet.

WARNING

TO AVOID THE POSSIBILITY OF A
FIRE HAZARD, DO NOT STORE
ANYTHING OR ALLOW DEBRIS OF
ANY KIND TO ACCUMULATE IN
THE BOTTOM OF THE DOOR, IN
AND AROUND THE
REFRIGERATION
COMPARTMENT, THE CABINET,
OR IN FRONT OF THE
EVAPORATOR AND CONDENSER
COILS.

COIN CHANGERS & OTHER
ACCESSORIES

The vender must have an MDB coin changer
installed and can have an MDB bill acceptor
installed. If the MDB coin changer and other MDB
accessories are not factory installed, refer to the
instructions received from the manufacturer of the
MDB coin changer and other MDB accessories for
proper set-up and installation.

The vender will support the following MDB coin
changers:

Multi-Drop Coin Mech (Domestic)

Coinco 9302GX
Coinco USQ G700 Series
Conlux USLZ-101
Conlux CCM5G
Mars 4510
Mars 6512

The vender will support the following MDB bill
validators:

Multi-Drop Bill Validators (Domestic)

Coinco BA30B, BA50, MAG30, MAG50
Mars VN2512, VN2502, VN2312
Conlux NBU-2111-12, NBM 3000 Series
Ardac 5500 Series

The vender will support the following MDB card
readers:

At publication, card reader dispositions were
not available. Contact card reader
manufacturer for proper installation and
setup.

LOADING CHANGE TUBES

Open the main door and enter the “FILL Coin Mech
(CF)” mode in the “CASH SET” (CS) sub-menu in
Programming (see Section B – Programming).

Load the coin mechanism with coins by inserting
coins in the coin mech’s separator. The display will
show the total value of coins as they are inserted.

Note: A low coin level in the coin tubes will

interfere with operation of the bill validator

.

For additional information about coin mechanisms,
refer to the specific manufacturer’s instructions.

«
...
4
5
6
7
8
...
»

Содержание DN552P-7













































































Отзывы:

Нет отзывов

Похожие инструкции для DN552P-7

Бренд: Howard McCray Страницы: 3

Бренд: Whynter Страницы: 17

Бренд: Federal Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды