dixell XC660D, Инструкции по установке и эксплуатации

Страница: 54 / 55

1592001850 XC660D GB r3.4 04.09.2017.docx XC660D 54/
55
Label Valori Menù Descrizione Parametri Limiti
HSF 50.0 Pr2
Maximum set point (fan) LSF÷150.0(°C) LSF÷302(°F) LSF÷FA20
(BAR , PSI , KPA)
PAO 30 Pr2
Alarm probe delay at power on 0 ÷ 255 (min.)
LAL -40.0 Pr1
Pressure alarm set low limit (compressors) -50.0÷HAL(°C); -58÷HAL(°F);
PA04÷HAL(BAR , PSI , KPA)
HAL 10.0 Pr1
Pressure alarm set high limit (compressors) LAL÷150.0(°C); LAL÷302(°F);
LAL÷PA20(BAR , PSI , KPA)
tAo 15 Pr1
Pressure/temperature alarm delay
(compressors)
0 ÷ 255 (min.)
ELP
-45.0 Pr2
Electronic pressure switch threshold -50.0÷STC1(°C) -58÷STC1(°F)
PA04÷STC1(BAR , PSI , KPA)
2LAL -50.0 Pr2
Pressure alarm set low limit, , suction 2 -50.0÷2HAL(°C); -58÷2HAL(°F);
3PA4÷2HAL(BAR , PSI , KPA)
2HAL 20.0 Pr2
Pressure alarm set high limit, suction 2 2LAL÷150.0(°C); 2LAL÷302(°F);
2LAL÷3P20(BAR , PSI , KPA)
2tAo 100 Pr2
Pressure/temperature alarm delay , suction 2 0 ÷ 255 (min.)
2ELP -50.0 Pr2
Electronic pressure switch threshold, suction
2
-50.0÷STC2(°C) -58÷STC2(°F)
3P04÷STC2(BAR , PSI , KPA)
SEr
999 Pr2
Working hour alarm set (tenth of ours) 1 ÷ 999 (0= disabled) (10 hour)
PEn 5 Pr2
Low Pressure switch maximum activations 0 ÷ 15
PEI 60 Pr2
Low Pressure switch activations time 0 ÷ 255 (min.)
SPr 1 Pr2
Number of compressors ON with faulty probe 0 ÷ 6
2PEn 5 Pr2
Low Pressure switch maximum activations,
suction 2
0 ÷ 15
2PEI 60 Pr2
Low Pressure switch activations time, suction
2
0 ÷ 255 (min.)
2SPr
1 Pr2
Number of compressors ON with faulty
probe, suction 2
0 ÷ 6
PoPr 50 Pr2
Capacity engaged with suction 1 probe failure 0÷100
LAF 0.0 Pr1
Low pressure alarm set (fan) -50.0÷HAF(°C); -58÷HAF(°F);
FA04÷HAF(BAR , PSI , KPA)
HAF
60.0 Pr1
High pressure alarm set (fan) LAF÷150.0(°C) LAF÷302(°F)
LAF÷FA20(BAR , PSI , KPA)
AFd 5 Pr2
Pressure alarm delay 0 ÷ 255 (min)
HFc YES Pr2
Compressor off with high pressure
(temperature) alarm
no – yES
dHF 5 Pr2
Interval between 2 compressors turning off
with high pressure (temperature) alarm
0 ÷ 255 (sec.)
PnF 5 Pr2
Fan pressure switch maximum activations 0 ÷15
PiF 60 Pr2
Fan pressure switch activations time 0 ÷ 255 (min)
FPr
1 Pr2
Fan ON with faulty probe 0 ÷ 6
ASH0
5 Pr2
Differential for low superheat pre-alarm 0.1 to 30.0°C/ 1 to 60°F
ASH1 240 Pr2
Delay for signalling low superheat pre-alarm 0÷255 sec
ASH2 5 Pr2
Low suction superheat alarm threshold 0.1÷15.0°C/ 1÷30°F
ASH3 120 Pr2
Delay for signalling low superheat alarm 0÷255 sec
ASH4
no Pr2
Switching off compressors with low superheat
alarm No, Yes
ASH5
5 Pr2
Differential to restart regulation after of low
superheat alarm with compressor stop 0.1÷15.0°C/ 1÷30°F
ASH6
1 Pr2
Delay to restart regulation after superheat >
ASH2+ASH5 0÷255 min
ASH7
10 Pr2
Superheat value to enable hot gas injecting
valve 0.1÷30.0°C/ 1÷60°F
ASH8 2 Pr2
Differential for ASH7 0.1÷15.0°C/ 1÷30°F
ASH9 nP Pr2
Probe selection for superheat monitoring nP(0) - P3(1) - P4(2)
dSEP nP Pr2
Dynamic Set point function enabled nP – P3 - P4