dixell XC660D, Инструкции по установке и эксплуатации

Страница: 53 / 55

1592001850 XC660D GB r3.4 04.09.2017.docx XC660D 53/
55
Label Valori Menù Descrizione Parametri Limiti
-999÷999(KPA)
inC
500 Pr2
Integral time, suction 1 0 ÷ 999 sec
2Pbd
5.0 Pr2
Proportional band for compressors
regulation, suction 2
0.1÷30.0(°C); 1÷50 (°F); 0.1÷10.0(BAR);
1÷150(PSI) 10÷1000(KPA)
2rS 0.0 Pr2
Band offset, suction 2 -12.0÷12.0(°C) -20÷20(°F)
-12.0÷12.0(BAR); -200÷ 200(PSI)
-999÷999(KPA)
2inC 500 Pr2
Integral time, suction 2 0 ÷ 999 sec
ton 60 Pr2
Time with Inverter at maximum capacity
before starting a new load
0÷255s
toF 30 Pr2
Time with Inverter at minimum capacity
before starting a new load
0÷255s
ESC
0.0 Pr1
Energy saving for compressors regulation -50.0÷50.0(°C) -90÷90(°F)
-20.0÷20.0(BAR) -300÷300(PSI)
-2000÷2000(KPA)
2ESC 0.0 Pr1
Energy saving for compressors regulation,
circuit 2 -50.0÷50.0(°C) -90÷90(°F)
-20.0÷20.0(BAR) -300÷300(PSI)
-2000÷2000(KPA)
OnOn 5 Pr2
Minimum delay between 2 switching on of the
same compressor
0 ÷ 255 (min.)
OFOn
1 Pr2
Delay between the switching off and on of the
same compressor
0 ÷ 255 (min.)
don
01:00 Pr2
Time delay between the insertion of two
different loads
0 ÷ 99.5 (min.10sec)
doF 00:30 Pr2
Time delay between switching off of two
different compressors
0 ÷ 99.5 (min.10sec)
donF 1:00 Pr2
Minimum time a stage stays ON 0 ÷ 99.5 (min.10sec)
MAon 0 Pr2
Maximum time a stage stays switched ON 0 ÷ 24 (hour)
FdLy no Pr2
'don' delay enabled also for the first request no - yES
FdLF no Pr2
'doF' delay enabled also for the first switching
off
no - yES
odo 20 Pr2
Regulation delay at power on 0 ÷ 255 (sec.)
LSE
-40.0 Pr2
Minimum set point (compressors) -50.0÷HSE(°C) -58.0÷HSE(°F)
PA04÷HSE(BAR,PSI,KPA)
HSE 10.0 Pr2
Maximum set point (compressors) LSE÷150.0(°C) LSE÷302(°F)
LSE÷PA20(BAR , PSI , KPA)
2LSE -40.0 Pr2
Minimum set point compressors, for circuit 2 -50.0÷2HSE(°C) -58.0÷2HSE(°F)
3P04÷2HSE(BAR,PSI,KPA)
2HSE
10 Pr2
Maximum set point compressors for circuit 2 LSE÷150.0(°C) LSE÷302(°F)
LSE÷3P20(BAR , PSI , KPA)
Lit 90.0 Pr2
Set point for liquid injection 0.0 ÷ 180.0°(°C) 32 ÷ 356(°F)
Lid
10.0 Pr2
Differential for liquid injection 0.1 ÷ 25.5° (°C) 1 ÷ 50° (°F)
LiPr nP Pr2
Probe selection for liquid injection nP - P3 - P4
Pb
5.0 Pr2
Proportional band for fan regulation 0.1÷30.0(°C) 1÷50 (°F) 0.1÷10.0(BAR)
1÷150(PSI) 10÷1000(KPA)
ESF
0.0 Pr2
Energy saving differential for fan regulation -50.0÷50.0(°C) -90÷90(°F)
-20.0÷20.0(BAR) -300÷300(PSI)
-2000÷2000(KPA)
PbES 0.0 Pr2
Band offset for fan regulation in ES -50.0÷50.0(°C) -90÷90(°F)
-20.0÷20.0(BAR) -300÷300(PSI)
-2000÷2000(KPA)
Fon 30 Pr2
Time delay between the insertion of two
different fan
0 ÷ 255 (sec)
FoF 15 Pr2
Time delay between switching off of two
different fan
0 ÷ 255 (sec)
LSF
10.0 Pr2
Minimum set point (fan) -50.0÷HSF(°C) -58.0÷HSF(°F)
FA04(FPb)÷HSF(BAR , PSI , KPA)