35
I25
I24
I23
I22
I21
I20
I19
I18
I17
I16
tr
sv
sl
pt
pl
no
nl
it
fr
fi
es
en
de
da
cz
Remove and clean the tool / squeegee
Cleaning the machine
Storage / parking of machine (machine is idle)
Store the machine with the lid slightly open.
This allows the tank to dry out. As a result, the formation of mould and
unpleasant smells can be reduced.
Service, maintenance and care
The machine's maintenance is pre-condition for trouble-free running and a long
life.
Service intervals
TASKI machines are built to the highest quality standards. This is supported by
internationally recognised quality control procedures. Electrical and mechanical
parts are subject to wear or aging if used for long periods of time.
Service centre
Should you contact us due to a malfunction or for placing an order, please
always state the type, description and the serial number of your machine.
You can find this information on the name plate of your machine, and the
address of your nearest TASKI partner can be found on the last page of this
manual.
Blades replacement
• Reach into the opening between the tank cover
and the tank (with the palm of your hand
upwards). Pull the locking bracket forward and
open the tank cover.
• Take the soiled solution hose from its holder.
(When emptying the tank, always follow the
regulations of the detergent manufacturer
regarding personal protective equipment.)
• Press the neck (1) of the hose together.
• Pull the lid from the hose and empty the
recovery tank.
• Remove the sieve (yellow), drain it and rinse it
thoroughly under flowing water.
• Lift the Flex tank, lay it at the lowest point in the recovery tank and drain it.
• Remove the empty Flex tank from the recovery tank and thoroughly rinse it
out with clean water.
• Remove the dirt and fluff from the vacuum air filter with a soft brush.
Caution:
A blocked suction filter can impair the suction performance.
• Thoroughly rinse out the recovery tank with clean water.
• Reinstall the sieve (yellow), the Flex tank and the suction filter.
• Switch the machine off using the keyswitch and remove the key.
• Release the adjustment lever and pull out the
tool.
• Clean the tools with water.
• Pull the two suction hoses from the squeegee support.
• Press the locking springs together. The
squeegee will thereby be released and can be
removed.
• Clean the squeegee with water using a brush.
Only clean and intact blades produce good vacuuming results!
Caution:
Never clean the machine with high water pressure or a water
hose.
The ingress of water into the machine might cause considerable
damage to mechanical or electrical parts.
• Switch the machine off using the keyswitch and remove the key.
• Wipe down the machine with a damp cloth.
1
• Switch the machine off using the keyswitch and remove the key.
• Press the Emergency Stop button.
Caution:
Only TASKI branded spare parts must be used, otherwise
warranties and liabilities will be omitted!
Symbols:
◊
= After use,
◊◊
= Every week,
◊◊◊
= Every month,
⊗
= Service light
Activity
◊ ◊◊ ◊◊◊ ⊗
page
Recharge batteries
31
Clean all parts marked yellow
Drain and clean the recovery tank
34
Empty and clean the Flex tank
34
Check the dirt sieve for residual matter, and clean
if necessary
34
Check solution supply pipe and filter and clean if
necessary
34
Check the vacuum air filter for dirt, and clean if
necessary
34
Cleaning the tools
35
Clean squeegee, check whether the blades are
worn and replace if necessary
35
Wipe down the machine with a damp cloth
35
Clean the tank lid seal, check for cracks and re-
place if necessary
36
Maintenance programs by TASKI service made by
TASKI technician
• In order to ensure operational reliability and
availability for use, the service must be carried
out when the service indicatior lights up (factory
setting 650 working hours) or at least once a
year.
Under rough or extreme working conditions and / or insufficient maintenance,
shorter intervals may be necessary.
• Lay the clean squeegee body on a firm surface (table, floor etc) with the
blades facing upwards.
• Evenly loosen the four Allen screws until the clamping device becomes
loose (do not fully screw out ther Allen screws).
• Pull out the blades, and either turn or replace them.
