Distech LonWorks ECL-203 Series Скачать руководство пользователя страница 13

13 / 16

Disposal

The Waste Electrical and Electronic Equipment (WEEE) Directive set out regulations for the recycling and disposal of products. The WEEE2002/96/EG
Directive applies to standalone products, for example, products that can function entirely on their own and are not a part of another system or piece of
equipment.

For  this  reason  Distech  Controls  products  are  exempt  from  the  WEEE  Directive.  Nevertheless,  Distech  Controls  products  are  marked  with  the  WEEE

symbol  , indicating devices are not to be thrown away in municipal waste.

Products must be disposed of at the end of their useful life according to local regulations and the WEEE Directive.

North American Emissions Compliance

United States

Changes or modifications not expressly approved by Distech Controls could void the user's authority to operate the
equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a
residential and commercial installation. This equipment generates, uses and can radiate radio frequency energy and,
if  not  installed  and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio
communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the  following
measures:

£

Reorient or relocate the receiving antenna.

£

Increase the separation between the equipment and receiver.

£

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

£

Consult the dealer or an experienced radio/TV technician for help.

Canada

This Class (B) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Classe (B) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Содержание LonWorks ECL-203 Series

















Отзывы: