background image

5 / 16

Subnetwork Bus Total Length

The  total  maximum  length  of  all  Subnetwork  buses,  including  both  the  length  of  the  Allure  Series  Communicating  Sensor  Subnetwork  bus  and  the
ECx-400 Series Subnetwork bus is 300 m (1 000 ft). The maximum length of the Allure Series Communicating Sensor Subnetwork bus is 200 m (650 ft).
The maximum length of the ECx-400 Series Subnetwork bus is 300 m (1 000 ft).

Sub-Network Bus Total Length: 300 m (1 000 ft) Maximum

Sub-Network Bus: 200 m

(650 ft) Maximum

Allure EC-Smart-Vue

Sub-Network Bus: 300 m

(1 000 ft) Maximum

ECx-400

Typical Compatible

Controller

Extension I/O Modules

ECx-400

Sub-Network Bus - Cat 5e Cable

with RJ-45 Connectors

Allure EC-Smart-Vue

Sub-Network Bus

ECx-400

2-Wire Shielded Cable

Figure 5:  Subnetwork Bus Overview Showing the Allure EC-Smart-Vue Subnetwork Bus and the ECx-400 Series Subnetwork Bus.

A controller can support a maximum of two Allure EC-Smart-Vue sensor models equipped with a CO

2

 sensor; the remaining connected models must be

without a CO

2

 sensor. See Table 1 for the quantity of room devices supported by each controller model.

For instance, if the controller model supports a subnetwork with 12 Allure EC-Smart-Vue sensors in total, then 10 sensor models must be without a CO2
sensor and the other two can be equipped with a CO2 sensor. To ensure proper operation, it is recommended to distribute the sensors throughout the
length of the subnetwork.

Cat 5e Cable with RJ-45 Connectors

Sub-Network Bus Total Length: 1 000 ft (300 m) Maximum

10x...

2x...

Bus: 600 ft (180 m) Maximum 

Allure EC-Smart-Vue

Sensor Sub-network

ECB-600

ECL-600

or

Typical

Controller

ECx-400

Sub-Network Bus

Figure 6:  Allure EC-Smart-Vue Sensor Subnetwork Length and Distribution

For ECB/ECL-PTU Series controllers, the maximum length between two consecutive devices on the sub-network bus
is 100 feet (30 m).

Содержание Allure EC-Smart-Vue Series

















Отзывы: