background image

12 / 16

7. To enter the GEN CFG submenu, press the down button 

 once.

8. Press the Menu button 

 several times until MOTION SENSITIVITY appears on the display. The current motion sensitivity level is shown.

OR

Screen Timeout: 30 seconds

9. Use the up and down buttons 

 

 to set the motion sensitivity level to 0 (low), 1 (medium - typical default setting), or 2 (high). The default and rec-

ommended level of sensitivity is medium (1) and should typically work with all installations. This setting should not be changed unless for some rea-
son you are experiencing false detections, then a low sensitivity (0) setting may be used, or if working with larger room installations a high sensitivity
(2) setting can be used.

10. Press the Menu button 

 once to apply the value.

11. Press and hold the Menu button 

 for 5 seconds to exit the configuration menu.

The  motion  indicator  LED  provides  a  visual  confirmation  of  motion  detection.  By  default,  the  indicator  (PIR  LED
jumper)  is  enabled.  If  you  wish  to  disable  it,  set  jumper  J18  to  Disabled.  See  Connector  and  Jumper  Location,
Identification and Configuration [pg. 3].

BACnet Network Access from the Sensor

To temporarily access the BACnet MS/TP LAN for commissioning and maintenance purposes (not available with either the ECB-PTU series controllers,
the ECLYPSE series controllers, or the ECB-VAVS), connect a BACnet MS/TP Adaptor to the audio plug port located on the lower edge of the Allure EC
Smart Vue sensor. Wire a standard ⅛” (3.5 mm) three-conductor stereo jack as shown below.

The  BACnet  MS/TP  Adaptor  must  have  an  electrically-isolated  RS-485  port.  Otherwise  a  ground  path  from  the
BACnet network will be made through the computer that will disrupt BACnet network communications.

To BACnet MS/TP 
Adaptor 

NET+

NET

-

Shield

LAN Access 

Connector

-  Temporary 

Commissioning and 
Maintenance 
Connection

-  No EOL Resistors are 

Necessary

BACnet MS/TP Adaptor 

with Isolated RS-485 Port

Cable Supplied with 
BACnet MS/TP Adaptor

NET+ (White)

NET- (Red)

Shield (bare)

Figure 13:  ⅛” (3.5 mm) Stereo Jack Connection for a Portable Router

Содержание Allure EC-Smart-Vue Series

















Отзывы: