background image

11 / 16

Set the LAN Type

Set the BAC/LON jumper for the type LAN in use: BAC for a BACnet network, LON for a L

ON

W

ORKS

 network.

BAC

LON

3.5 mm (1/8

”) Network 

Access Jack

Network Type 

Jumper

Figure 11:  BAC/LON Jumper Set to the BAC (BACnet) Position when used with ECBSeries Controllers

BAC

LON

3.5 mm (1/8

”) Network 

Access Jack

Network Type 

Jumper

Figure 12:  BAC/LON Jumper: Set to the LON (L

ON

W

ORKS

) Position when used with ECL Series Controllers

Setting Up an Allure EC-Smart-Vue Sensor Equipped with a Motion Sensor

The following procedure describes how to commission and test an Allure EC-Smart-Vue sensor equipped with a motion sensor as well as adjust the mo-
tion sensitivity (Allure EC-Smart-Vue M/-CM/-HM/-CHM sensors).

1. Connect an Allure EC-Smart-Vue sensor equipped with a motion sensor to the controller with a Cat 5e patch cable.
2. After a 30-second warm-up period, if movement is detected, the motion sensor light will turn on.
3. To test the sensor functionality, aim the sensor in the direction you want to detect motion and walk at a normal pace across the typical detection zone

and verify that the sensor light turns on. The light will turn on and after 2 seconds of non-movement, the motion sensor light will turn off.

4.  Now  to  set  the  motion  sensitivity,  on  the  Allure  EC-Smart-Vue  sensor,  press  and  hold  the  Menu  button 

  for  5  seconds  to  enter  the  password

menu. 10000 is shown on the display.

OR

Screen Timeout: 15 seconds

5. Press the down button 

 to set the number to 9995 (this is the default password).

OR

Screen Timeout: 15 seconds

6. Press the Menu button 

 to submit the password. Upon submitting the password, the GEN CFG menu appears on the display.

OR

Screen Timeout: 30 seconds

Содержание Allure EC-Smart-Vue Series

















Отзывы: