Disaster Area Designs DMC-6 Gen3 Скачать руководство пользователя страница 4

 of 

4

20

2.  Controls and Connections 

CONTROL PANEL

The DMC-6 Gen3 and DMC-8 Gen3 have the same basic controls:  Buttons A, B, C, and D are located on the left side of the device, 
and the SAVE / UP and TAP / DOWN buttons are on the right side.  The DMC-8 Gen3 has additional TAP and FAVE buttons at the far 
right side of the control panel.  Please note that throughout this manual we will refer to the TAP / DOWN and the DOWN buttons 
interchangeably.  

REAR PANEL

MIDI Output:

Standard 5-pin MIDI output, connects to your first MIDI pedal input.

MIDI Input:

The MIDI output jack doubles as a MIDI input using a Disaster Area MIDI Y-cable (sold separately.)  The MIDI input 

allows the DMC Gen3 to accept incoming MIDI messages and merge them in with its own data stream.

Expression Input: The black jack is a multi-function connector that can accept an expression pedal or a momentary footswitch.  Consult 
the Expression section for more details.

DC 9V:

Standard DC power supply input, 9V center negative.  The DMC Gen3 requires approximately 80mA if used by itself.  

If an external USB HOST device is connected, the DMC will need to be supplied with enough current to power both itself and the USB 
device.

USB MIDI:

The standard DMC firmware allows the USB port to function as a MIDI interface for your compatible PC, Mac, or iPad 

(using the Apple Camera Connection Kit.)  The DMC will receive and send MIDI messages over USB for device control.
USB HOST:

If the USB Host firmware is installed, the DMC USB port may be used to send and receive MIDI messages to 

supported USB devices.

Status Indicator: This is just a little LED that blinks to let you know the pedal is working.  It also blinks at a slower rate to indicate that 
the pedal is in boot loader mode during a firmware update.

MultiJacks 1-3:

The red, white, and blue connectors are our astounding MultiJacks!  The MultiJacks can do all kinds of cool stuff, like 

receive expression or tap tempo, send taps to your devices, or even send MIDI to additional devices.

Disaster Area Designs 

DMC-6 / DMC-8 Gen3

Содержание DMC-6 Gen3





















Отзывы: