Disaster Area Designs DMC-6 Gen3, Руководство пользователя

Страница: 19 / 20

of 19 20
17. Setup Mode
Setup Mode allows you to configure every aspect of your DMC Gen3 Controller. Please refer to Section 4 for details on entering and
navigating Setup Mode.
SETUP PARAMETERS:
PRST - Preset Mode
Sets the number of available preset banks
Range: 0-63 banks
DEV - Number of Connected Devices
Sets the number of connected MIDI devices
Range: DevA (one device) - DevF (six devices)
DevA / DevB / DevC - Device Control selection
DevD / DevE / DevF
Available Devices:
General MIDI
Strymon Timeline*, Mobius, BigSky
Eventide H9* or Factor series (Timefactor*, Modfactor,
Pitchfactor, SPACE)
Line 6 M5, M9*, M13*
Chase Bliss Warped Vinyl, Wombtone (mk.II versions
only,) Gravitas, Spectre, Tonal Recall
EHX HOG2 synthesizer
Pigtronix Echolution 2 / Deluxe / Filter Pro / Ultra Pro
Boss DD-500
Alexander Oblivion, Super Radical Delay
Panda Audio Future Impact I
Source Audio Neuro / SoundBox Hub
Source Audio Nemesis Delay
Free The Tone FT-1Y Flight Time
Empress Reverb, Tremolo 2
Digitech Whammy V Classic, Chords
Zoom MultiStomp MS-50G, MS-60B, MS-70CDR
MIDI Notes - Used for controlling Ableton Live or DAW
Devices marked with * may be controlled by the DMC
Looper Modes.
The DMC Looper Modes will use the highest
numbered device with looper capability.
LOOP - Looper Device selection
Selects the device the DMC will use for looper control
Range: DevA - DevF
If the selected device does not support looper control,
Looper Mode will display “OFF” when entered.
EXP - Expression Pedal input (black jack) configuration
OFF - disable expression pedal input jack
EXPR - expression pedal
LPLV - looper volume level
SPLT - split expression, sends looper volume level in
looper modes and expression in all others
TAP - tap tempo footswitch input
LATC - latching freeze / hold footswitch input
FAVE - favorite preset load / save footswitch input
BANK - advance to the previous mode
E CH - Expression Pedal input channel selection
A B C Expression Pedal enable / disable
If the location shows as zero, the controller will not
transmit expression or looper level on that channel
If all three locations show as zero, no expression will
be sent
MJ1 / 1CH - MultiJack 1 (RED) configuration
MJ2 / 2CH - MultiJack 2 (WHITE) configuration
MJ3 / 3CH - MultiJack 3 (BLUE) configuration
Please refer to Section 13 for MultiJack details
ROLL - Optional side roller configuration
OFF - disable expression roller, this should be
selected if no roller is installed
EXPR - expression pedal
LPLV - looper volume level
SPLT - split expression, sends looper volume level in
looper modes and expression in all others
R CH - Optional side roller channel selection
A B C Side Roller enable / disable
If the location shows as zero, the controller will not
transmit expression or looper level on that channel
If all three locations show as zero, no expression will
be sent
FAVE - FAVE configuration (DMC-4 only)
OFF - FAVE is disabled, this should be selected if
using a DMC-6 Gen3
TAP - FAVE functions as tap tempo footswitch
LATC - FAVE functions as latching freeze / hold
footswitch
FAVE - FAVE loads and saves the Favorite preset
TUNE - FAVE activates the tuner on supported
devices
BANK - FAVE advances to the previous mode
F CH - FAVE channel selection
A B C FAVE enable / disable
If the location shows as zero, the controller will not
transmit commands on that channel
If all three locations show as zero, the controller will
send no commands when FAVE is pressed
EDSP - Expression Pedal Display
d ON - Changes to the expression pedal, side roller,
and MultiJack will be shown on the display briefly.
Expression Pedal will be prefixed with "E,"
Roller with "R," and MultiJack with “J."
d OFF - no expression values will be displayed
Disaster Area Designs DMC-6 / DMC-8 Gen3