DirecTV Advanced Installation Meter Скачать руководство пользователя страница 84

Страница: 84 / 92

Updating the Meter

You can update your AIM as new features become available. You can update the

AIM application, the AIM’s database (which includes reference information used by

the AIM), or both the application and database.
When you update the meter firmware, you must plug the AIM into a power outlet

using the AC power adapter.
To update the firmware:

Plug the AC power adapter into a power outlet. Plug the other end of the power

adapter into the AIM’s power input connector.

Press

CONFIG

to go to the

CONFIGURATION

screen.

Use

to highlight

Firmware Upgrade

and press

SELECT

to go to the

FIRMWARE UPGRADE

screen.

Use

to highlight the type of update you want to perform and press

SELECT

Tip:

To view the current AIM firmware version,

press

CONFIG

to go to the

Configuration

screen. Then use

to highlight

Firmware

Versions

and press

SELECT

Содержание Advanced Installation Meter





























































































Результаты поиска

Содержание Advanced Installation Meter

Отзывы:

Похожие инструкции для Advanced Installation Meter

Бренды по названию

Популярные бренды

DirecTV Advanced Installation Meter, Руководство пользователя

Результаты поиска

Содержание Advanced Installation Meter

Отзывы:

Похожие инструкции для Advanced Installation Meter

Бренды по названию

Популярные бренды