3
© 2012 Directed. All rights reserved.
G Wagon Installation
1. Lower the steering column and extend it to its maximum.
2. Grasp the plastic trim below the instrument cluster and pull toward you.
3. Continue removing the boot around the steering column and pull it away from the dash as far as itwill go.
4. Reach in the behind the EIS and unplug the two plugs, (1) green plug and (1) blue plug, and unplug them.
5. Connect the XPRESS
START
harness in line with the plugs and connect the opposite end into the rear of the EIS.
6. Remove the under dash panels using a T-20 driver.
7. Route the XPRESS
START
harness to a location where the starter can be mounted away from heat and moving parts.
8. Connect the XPRESS
START
to the T-harness and securely mount it.
9. Drill a 3/4” hole for the valet switch in an easily accessible location under the dash.
10. Remove the valet switch from the T-harness and mount it in the hole just drilled and reconnect the wires.
11. Start the vehicle with the key and let it run for 60 seconds then turn it off.
12. Press the panic button on the keyfob once and test the remote start.
13. Reassemble the under dash.
14. Reinstall the steering wheel boot.
Installation
1.
Lower the steering column and extend it to its maximum.
2.
Grasp the plastic trim below the instrument cluster and pull toward you.
3.
Continue removing the boot around the steering column and pull it away from the dash as far as it
will go.
4.
Reach in the behind the EIS and unplug the two plugs, (1) green plug and (1) blue plug, and
unplug them.
5.
Connect the Smartkey Starter® harness in line with the plugs and connect the opposite end into
the rear of the EIS.
6.
Remove the under dash panels using a T-20 driver.
7.
Route the Smartkey Starter® harness to a location where the starter can be mounted away from
heat and moving parts.
8.
Connect the Smartkey Starter® to the T-harness and securely mount it.
9.
Drill a 3/4” hole for the valet switch in an easily accessible location under the dash.
10.
Remove the valet switch from the T-harness and mount it in the hole just drilled and reconnect the
wires.
11.
Start the vehicle with the key and let it run for 60 seconds then turn it off.
12.
Press the panic button on the keyfob once and test the remote start.
13.
Reassemble the under dash.
14.
Reinstall the steering wheel boot.
Remove steering wheel boot
EIS plug location at rear of EIS
Copyright 2012 Midcity Engineering®
EIS plugs
Installation
1.
Lower the steering column and extend it to its maximum.
2.
Grasp the plastic trim below the instrument cluster and pull toward you.
3.
Continue removing the boot around the steering column and pull it away from the dash as far as it
will go.
4.
Reach in the behind the EIS and unplug the two plugs, (1) green plug and (1) blue plug, and
unplug them.
5.
Connect the Smartkey Starter® harness in line with the plugs and connect the opposite end into
the rear of the EIS.
6.
Remove the under dash panels using a T-20 driver.
7.
Route the Smartkey Starter® harness to a location where the starter can be mounted away from
heat and moving parts.
8.
Connect the Smartkey Starter® to the T-harness and securely mount it.
9.
Drill a 3/4” hole for the valet switch in an easily accessible location under the dash.
10.
Remove the valet switch from the T-harness and mount it in the hole just drilled and reconnect the
wires.
11.
Start the vehicle with the key and let it run for 60 seconds then turn it off.
12.
Press the panic button on the keyfob once and test the remote start.
13.
Reassemble the under dash.
14.
Reinstall the steering wheel boot.
Remove steering wheel boot
EIS plug location at rear of EIS
Copyright 2012 Midcity Engineering®
EIS plugs
Remove steering wheel boot
EIS plug location at rear of EIS
