manualshive.com logo in svg

Dion Forage Blower, Руководство оператора

Поделиться
Скачать
Dion Forage Blower Скачать руководство пользователя страница 35

Page 24

ADJUSTMENTS - MAINTENANCE

AUGER SCREW INTERMEDIATE BELT
TENSION - FIGURE 28

Adjust the intermediate belt (item 1) tension by turning
the adjusting nut (item 2) of the tightener (item 3).

To make sure the spring (item 4) is sufficiently tightened,
leave a 1/16" to 3/32" (1,5 to 3,4 mm) gap between the
spring spirals.

Next, adjust the stop bolt (item 5) by loosening the nut
(item 6) so that a 1/8" (3 mm) gap is obtained between
the bottom of the tightening arm and the stop bolt.
Retighten well the nut

AUGER SCREW DRIVE BELT TENSION
FIGURE 29

Set the clutch control arm (item 1) to the ON position.

Adjust the tightener (item 6) tension on the auger screw
drive belts (item 3) with the tension spring (item 2) nuts
(item 4) to obtain a normal tension. Leave a 1/32" (0,8
mm) gap between the spring spirals.

The locking nuts (item 5) should be adjusted to leave a
1/4" (6,4 mm) gap as shown in the illustration. The
clutch control arm (item 1) should be in the ON position.

GUARDS REMOVED FOR ILLUSTRATION PURPOSES

GUARDS REMOVED FOR ILLUSTRATION PURPOSES

Figure 28 Auger screw intermediate belt tension

Figure 29 Auger screw drive belt tension

Содержание Forage Blower












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды