Dinstar SBC3000 Скачать руководство пользователя страница 49

Страница: 49 / 71

3 Configurations on Web Interface

SBC3000 Session Border Controller

Figure 3-26 Core SIP Trunk

Table 3-24 Core SIP Trunk

Name

The name of the core SIP trunk. It cannot be modified after the access SIP trunk has been

added successfully

Description

The description of the core SIP trunk

Interface

The SBC3000 device’s Ethernet interface configured to connect the core SIP trunk k. It

can be eth0, eth1, eth2, eth3 or VLAN

Transport

Select a transport protocol for the core SIP trunk. It can be UDP, TCP or TLS

SIP Port

The core SIP trunk’s SIP listening port on the Ethernet interface of SBC3000

IPv4/IPv6

Select a network protocol for the core SIP trunk. It can be IPv4 or IPv6.

By default, the network protocol is IPv4

Signaling DSCP

The QoS tag of SIP signaling messages

Media DSCP

The QoS tag of media messages

Near-end NAT

Near-end NAT defaults to disabled. If it is enabled, the contact IP address contained in

SIP messages sent out by SBC3000 will be turned into the outbound IP address of public

network.

If NAT is enabled, you need to fill in the outbound IP address of public network.

Rate Limit

The maximum RPS(registrations per second), CPS(calls per second) and total call

volume of the core SIP trunk. Please refer to3.4.5

Codec

The codecs that the core SIP trunk supports. Please refer to 3.4.7

Blacklist

Select a blacklist for the core SIP trunk. Calls given by the caller numbers on the blacklist

cannot be routed by the core SIP trunk. Please refer to 3.4.6

Whitelist

Select a whitelist for the core SIP trunk. Calls initiated by the caller numbers on the

whitelist will be directed by the core SIP trunk. Please refer to 3.4.6

If no black list and white list are selected for the core SIP trunk, all calls can be routed

by the core SIP trunk.

Inbound

Manipulation

Select a number manipulation rule or a number pool for the core SIP trunk. When a call

routed by the SIP trunk matches the manipulation rule, its number will be manipulated.

Please refer to 3.4.8 and 3.4.9

DTMF

DTMF is short for Dual Tone Multi Frequency;

Содержание SBC3000







































































Результаты поиска

Содержание SBC3000

Отзывы:

Бренды по названию

Популярные бренды

Dinstar SBC3000, Руководство пользователя

Результаты поиска

Содержание SBC3000

Отзывы:

Бренды по названию

Популярные бренды