Dini Argeo 3590E Series Скачать руководство пользователя страница 26

Страница: 26 / 49

3590EXTLWBCIO, CPWELW series indicator

E-LW_01_14.03_EN_U

5.5 SYSTEM STATUS INFO

Below there are the statuses shown on the display on the first line or the single line in the case of active zoom on CPWE.

MESSAGE

DESCRIPTION

DISABLED

The DOSAGE START input is OPEN. Also in this status, with flow greater than the
minimum, the instrument totalises the weight in transit, but the error checks are not
active.

WAITING

If a input is linked to consensus function, when the input is closed, the message will be

showed on the display and wait for the start command.

START

The instrument waits for the reaching of the hourly flow (<<tAr.tiM>> step

TECH.MAN.REF.

START DELAY

The instrument waits for the time set in the

<<dELAY>>

step before enabling the

dosage.

STOP DELAY

The instrument waits for the time set in the

<<dELAY>>

step before disabling the

dosage.

WAIT FOR FILLING

The instrument is in the filling phase.

LOCKED: FILLING

<<LOK.TIM>>

time has passed from when the filling has been enabled and the weight

is still the minimum filling threshold

<<StArt.W>>

, the display shows this message.

LOCK

Indicates that the dosage has stopped due to one of the following reasons:
- FLOW out of TOLERANCE RANGE

- WEIGHT LESS THAN MINIMUM or GREATER THAN MAXIMUM

PAUSE

The instrument is in the PAUSE status.

ALARM

The instrument is in the alarm condition, due one of the following reasons:
-

FLOW ALARM > MAX

FLOW out of TOLERANCE RANGE

WEIGHT ALARM > MAX

< MIN

: WEIGHT LESS THAN MINIMUM or GREATER

THAN MAXIMUM

DOSAGE

The instrument is in the dosage condition.

- OUT OF FLOW ! -

The instrument is in the underload or overload condition.

FLOW > MAX

The calculated flow is over

<<Max.F.r>>

UNLOAD SPEED (DAC)

The instrument has entered the MANUAL MATERIAL UNLOADING function (“

MANUAL

ENABLING OF THE DOSAGE OUT OF THE CYCLE, WITHOUT INCREMENT THE

TOTALS

”).

5.6 MESSAGES OF THE INSTRUMENT

While using the indicator, it is possible to incur the following errors:

INSIDE THE SET-UP OR MENU

MESSAGE

DESCRIPTION

Err.Mot.

The weight is unstable therefore it may not be acquired.

C.Er. – 38
C.Er. – 39

When carrying out the multirange or multidivisional calibration, the ranges have not been

entered in an increasing manner (RANGE 1 < RANGE 2 < RANGE 3).

C.Er. – 36

During the calibration some internal negative points have been calculated:

the calibration point is less than the zero point.

the signal is negative (check the connections)

C.Er. – 37

During the calibration some internal points less than the minimum value have been calculated:

the calibration point is equal to the zero point.

A capacity too high in relation to the division has been set.

Содержание 3590E Series


















































Результаты поиска

Содержание 3590E Series

Отзывы:

Бренды по названию

Популярные бренды

Dini Argeo 3590E Series, Руководство пользователя

Результаты поиска

Содержание 3590E Series

Отзывы:

Бренды по названию

Популярные бренды