manualshive.com logo in svg

DINGO D4040P, Руководство пользователя, Страница: 7 / 24

Поделиться
Скачать
DINGO D4040P Скачать руководство пользователя страница 7

7

   Dingo D4040P User Guide

c.

 Test the solar panel connection 

by touching the negative (-) 
wire from the solar panel onto 
the Test terminal (TEST).
•If the alarm led does not flash 
then it is OK. 
•If the alarm led flashes quickly 
then it is 

not

 OK. Check the 

polarity and test again. 

(There 

must be some light on the solar 
panels for this test to work). 

If OK connect to the Solar 
negative (-) terminal.

d.

 Connect the negative (-) wire 

from DC load circuit to the 

load negative (-) terminal and 

connect the positive wire from 

the load to the load positve 

(+) terminal. Test that the load 

circuit works. The controller 

is protected against load short 

circuits, but cannot protect your 

load devices if you reverse the 

connection to them. 

Now, set 

the system voltage - see pg.10 

Note: The controller is protected 

against short circuit on the solar input.

Fig. 4

TEST





BOOST

V

+

-

+

-

+

-

Battery

+

–

flashes if

  wrong

test

here

Test
Solar

2

Solar

–

+

TEST





BOOST

V

+

-

+

-

+

-

Battery

+

–

Solar

–

+

Connect
Load

3

Load

+

–

Содержание D4040P

























Отзывы:

Нет отзывов