DINGO D4040P Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

DINGO D4040P Скачать руководство пользователя страница 12

Dingo D4040P User Guide

12

Monitoring your system

This controllers’s advanced monitoring functions provide you
with unparalleled information about your system. Here are some
questions that your controller can answer:

How much energy have I collected today?

The top-level IN screen shows how many Amp hours have been
collected today.

How much energy have I used today?

The top-level OUT screen shows how many Amp hours the load
has used today.

What voltage did the battery reach?

VMAX shows today’s maximum voltage since midnight; VMIN
shows today’s minimum voltage. Both are in the DATA sub-menu.
The actual battery voltage is shown on the BATV screen.

What is the charge current?

The top level CHRG screen displays the charge current. This
is the total current from all charge sources. The current which
actually flows through the controller is called internal. In larger
systems, there can be current which does not flow through the
controller. This is called external.

«
...
10
11
12
13
14
...
»

Содержание D4040P

























Отзывы:

Нет отзывов