DINGO D4040P Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 24

DINGO D4040P Скачать руководство пользователя страница 11

11

Dingo D4040P User Guide

Programs

0:

Liquid Electrolyte Battery with Low Battery Disconnect option

(p.18)

1:

Sealed batteries (AGM or Gel) with Low Battery Disconnect option

2:

Liquid Electrolyte Battery with Light Controller option

(see p.19)

3:

Sealed batteries (AGM or Gel) with Light Controller option.

4:

Customised setup. Choosing this program will require you to set a

number of additional parameters.

(see Reference Manual)

d. When battery voltage is correct, long-push to set it.

3. Set your program (! Important)

The Dingo comes with a number of pre-set programs, to
make configuration easy for most installations.
a. Short-push to move from “VOLT” to “PROG”.
b. Long-push and the program number will start flashing.

c. Short-push to select the best program for your batteries:
d. When the program shown is correct, long-push to set it.

4. Set the Battery Capacity

Note: BCAP setting does not affect battery charging.

a. Short-push to move from “PROG” to “BCAP”.
b. Long-push and the battery capacity will start flashing.
c. Short-push to choose the correct battery capacity for your

system in Ampere hours (Ah). (Settings over 1000Ah display
in thousands - e.g. 1600 Ah shows as “1.6”. Note: Look for
the decimal point, eg 20=20Ah, 20.0=20,000Ah) If unsure,
check your battery manual or consult your battery supplier.

d. Long-push to keep the chosen value

«
...
9
10
11
12
13
...
»

Содержание D4040P

























Отзывы:

Нет отзывов