Dimplex UP 75-25PK Скачать руководство пользователя страница 20

EN-6

452115.66.53 · FD 9712

English

UP 75-25PK - UP 75-32PK

6.2 Navigation

Key lock

Locking the control keys is intended to prevent the settings from
being changed by mistake or without authorization.
If the key lock is activated, it is not possible to switch to settings
mode. It is still possible to switch to the settings view, however.
The key lock can be activated or deactivated by pressing the key
for more than 10 seconds. All yellow LEDs light up briefly to indi-
cate that the activation or deactivation is complete.

Factory settings

During  the  first  commissioning,  the  pump  starts  with  the  max.
characteristic curve

6.3 Settings mode

Pressing  the  key  briefly  switches  between  the  status  view  and
the settings view. 
If the key is pressed for between 2 and 10 seconds, the display
switches  to  settings  mode  if  the  operating  panel  keys  are  not
locked.  As soon as  the settings  appear, they can be  changed.
The settings appear in a specific order and can be run through in
a loop. Once the key is released, the display switches back to the
status display and the last setting is saved.

UP 75-25(32)PK

This  pump  version  can  either  be  controlled  externally  via  the
PWM profile A or run on a fixed characteristic curve according to
the selected speed.
One of four speed levels can be set.

With external control, the pump runs at the speed specified
by the PWM signal.

Without  external  control,  the  pump  runs  at  the  maximum
speed of the relevant speed level.

PWM profile A (heating)

Changing the settings on the UP 75-25(32)PK

If the pump is switched on, it initially runs with the factory presets.
The current operating status is shown in the display.
1)

Press the key to switch to the settings view. The LEDs indi-
cate the current setting for 2 seconds.

2)

If the key is not actuated for more than 2 seconds, the dis-
play switches back to the “operating status” view, where the
current power consumption is shown.

3)

If the key is pressed for longer than 2 seconds, the circulat-
ing pump switches to settings mode. The LEDs start to flash
and indicate the current setting. If the keyboard is locked, it
is not possible to switch to settings mode. In this case, the
keyboard  must  first  be  unlocked  by  pressing  the  key  for
longer than 10 seconds.

4)

The  setting  can  then  be  changed  within  10  seconds  by
pressing the key. Each key activation switches to a different
control curve.

5)

The  process  must  be  repeated  until  the  desired  setting  is
achieved. If you miss the desired setting, the entire setting
process must be started again from the beginning, as it is
not possible to go back within the settings menu.

6)

If the key is not pressed for longer than ten seconds, the dis-
play switches back to the status display. The last setting was
saved and the relevant control curve is applied.

7)

It is advisable to check by pressing the key again so that the
display switches to the setting view and the LEDs indicate
the current setting for 2 seconds.

8)

If the key is not pressed for longer than 2 seconds, the dis-
play switches back to the status view.

> 10 s.

PWM

profile A

LED1

Red

LED2

Yellow

LED3

Yellow

LED4

Yellow

LED5

Yellow

Level 1

Level 2

Level 3

Level max.

> 10 s.

SETTING MENU

PERFORMANCE 

SELECTED SETTING

> 2 s.

X

10 s.

SELECTED SETTING

2 s.

Содержание UP 75-25PK













































Отзывы: