Digitus DN-7059-2 Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 156

background image

141

4-2 Troubleshooting

If you found the router is working improperly or stop responding to you, don’t
panic! Before you contact your dealer of purchase for help, please read this
troubleshooting first. Some problems can be solved by you within very short
time!

Scenario

Solution

Router is not
responding to me when
I want to access it by
web browser

a. Please check the connection of power cord

and network cable of this router. All cords and
cables should be correctly and firmly inserted
to the router.

b. If all LEDs on this router are off, please check

the status of A/C power adapter, and make
sure it’s correctly powered.

c. You must use the same IP address section

which router uses.

d. Are you using MAC or IP address filter? Try to

connect the router by another computer and
see if it works; if not, please restore your router
to factory default settings (pressing ‘reset’
button for over 10 seconds).

e. Set your computer to obtain an IP address

automatically (DHCP), and see if your
computer can get an IP address.

f. If you did a firmware upgrade and this

happens, contact your dealer of purchase for
help.

g. If all above solutions don’t work, contact the

dealer of purchase for help.

Can’t get connected to
Internet

a. Go to ‘Status’ -> ‘Internet Connection’ menu,

and check Internet connection status.

b. Please be patient, sometime Internet is just that

slow.

c. If you connect a computer to Internet directly

before, try to do that again, and check if you
can get connected to Internet with your
computer directly attached to the device
provided by your Internet service provider.

«
...
148
149
150
151
152
...
»

Содержание DN-7059-2





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DN-7059-2

Бренд: NETGEAR Страницы: 2

Бренд: Salto Страницы: 3

Бренд: Ubiquiti Страницы: 26

Бренд: Universal Scientific Industrial Co. Страницы: 19

Nfiniti Airstation WHR-G300N

Бренд: Buffalo Tech Страницы: 48

Бренд: TP-Link Страницы: 2

Бренд: Last Mile Gear Страницы: 19

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 25

Бренд: NEC Страницы: 25

Бренд: NEC Страницы: 26

Бренд: NEC Страницы: 34

Бренд: NEC Страницы: 46

Бренд: NEC Страницы: 48

Бренд: MC Crypt Страницы: 5

Бренд: Blink Страницы: 3

BLUESOCKET 3040

Бренд: ADTRAN Страницы: 6

BLUESOCKET 2135

Бренд: ADTRAN Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды