background image

© 2022 Digitrax, Inc. 

www.digitrax.com

 8

8

1.6  Best practice System Shut Down:

1.  Press the DT602 PWR key and then the TRK_OFF or B-softkey.  The TRACK 

STATUS led should go dark when the TRK is powered OFF.

2.  Move the command station’s 

MODE

 switch to the 

SLEEP

 position and wait 5 

seconds.

3. 

For zero power draw, turn off the power to the whole DCC layout system.

4. 

Alternately power to the CS can be left on if desired.  In “

sleep

” mode, this CS 

consumes very little energy.  In this state the CS provides keep alive power to all 

throttles that are connected to LocoNet, and DT602/UT6’s can be configured to 

Charge their batteries during this sleep time.

2.0  Resuming your session

When you are ready to resume your session:

1.  Turn on the power to the system 

2.  Move the command station’s 

MODE

 switch to the 

RUN

 position.

3.  If required press the DT602 PWR key at bottom left and then the TRK_ON or 

A-softkey.  The TRACK STATUS led will light when the TRK is powered ON. By 

default the will resume in whatever state it is powered off in

2.1  Programming DCC decoders:

Figure 1 and Section 1.3 detail connecting an Isolated program track for Service mode 

CV programming.

2.1.1  Service mode programming 

Service mode programming broadcasts a message to all decoder equipped locos that 

are on a programming track connected to PA/PB terminals.  Because this is a broadcast 

method and will affect all locos, you will need to set up this programming track so that 

the programming instructions only go to the loco you want to program. 

  

Your sends these broadcast commands using the 

Program A(PA)

 and 

Program B(PB)

 outputs.

Follow the steps outlined in your Throttle and decoder documentation to program your 

decoder equipped locomotives.

2.1.2  Ops mode programming

Ops mode 

write

 CV programming is done on the layout tracks connected to any boost-

er, with programming directed to a 

specific decoder address on the main layout tracks

.  

Operations mode programming is used to make changes to locos while they are running 

on the layout main tracks.  

See your throttle manual for further instructions on Ops 

mode programming.

If the has Booster Transponding mode enabled (OPSW29 =T, default) then a 

compatible Transponding decoder on the track supplied by the booster RA/

RB terminals will also be able OPS Read CV’s, as well as writing values.  See 

section 

6.0

.

Содержание DCS240

























Отзывы: