DigiTech JamMan SOLO XT Скачать руководство пользователя страница 65

Страница: 65 / 72

Factory restore

The Factory Restore procedure will return the JamMan Solo XT back to its original

factory state by:

• Setting all Setup menu parameters back

to their factory default state

• Erasing all internal loop memories

• Restoring the original 15 loops that

shipped with the JamMan Solo XT

WarNINg!

The Factory Restore procedure will erase all loops from the JamMan Solo XT’s

internal memory. This procedure is permanent and cannot be reversed. Use the Factory Restore

procedure with caution. It is recommended you back up your internal loops to your computer

using the JamManager XT software and USB connection before performing this procedure. Factory

Restore does not affect any loops on the optional external memory card.

To perform the Factory Restore procedure:

Press and hold the

<STORE>

button

and apply power to the JamMan Solo

XT. Wait until the display shows

then release. The

<STORE>

button

LED will now be flashing.

Press the

<STORE>

button once. The

display will now show

(Factory

Restore?).

To abort this procedure, press the

<PEDAL SWITCH>

. To confirm the

restore procedure, press and hold the

<STORE>

button until

buS

appears

in the display. This indicates the

JamMan Solo XT is busy performing

the restore. Wait for the The JamMan

Solo XT to complete the procedure,

indicated by loop memory

being

shown in the display.

Содержание JamMan SOLO XT









































































Результаты поиска

Содержание JamMan SOLO XT

Отзывы:

Бренды по названию

Популярные бренды

DigiTech JamMan SOLO XT, Руководство пользователя

Результаты поиска

Содержание JamMan SOLO XT

Отзывы:

Бренды по названию

Популярные бренды