DigiTech JamMan SOLO XT Скачать руководство пользователя

Страница: 36 / 72

Erasing All Loops (External Memory Card)

The JamMan Solo XT allows you to quickly erase all loops from external memory. The

erase procedure only erases JamMan Solo XT loop data. All other data and files on

the card are left untouched.

WarNINg!

Erasure of all loops cannot be undone! You should backup any loops you wish to keep,

using the JamManager XT loop librarian management software, before erasing all loops.

To erase all loops from the external memory card:

Ensure an external memory location

has been selected (the

CARD MEM

LED should be on). If the

CARD MEM

LED is off, press and hold the

<UP>

DOWN>

button until the LED lights.

Press and hold the

<STORE>

button

for approximately four seconds until

the display

shows

ErC

(Erase Card)

then release. The

STORE

button LED

will begin flashing, waiting for erase

confirmation.

Press the

<STORE>

button again. The

display will read

(Erase Loops?).

To continue with the erasure of all

loops from the external memory

card, press and hold the

<STORE>

button until the display

reads

buS

then

release. Wait for the JamMan Solo

XT to finish erasing all loops from

external memory. To abort procedure,

press the

<PEDAL SWITCH>

Содержание JamMan SOLO XT









































































Результаты поиска

Содержание JamMan SOLO XT

Отзывы:

Похожие инструкции для JamMan SOLO XT

Бренды по названию

Популярные бренды

DigiTech JamMan SOLO XT, Руководство пользователя

Результаты поиска

Содержание JamMan SOLO XT

Отзывы:

Похожие инструкции для JamMan SOLO XT

Бренды по названию

Популярные бренды