Digisol DG-GS4628S Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 25

Digisol DG-GS4628S Скачать руководство пользователя страница 21

Hardware Installation

2-8

Step 3: Push the SFP transceiver along the guide rail gently until you feel the transceiver

snap into place at the bottom of the line card.

Note: the SFP transceiver is hot swappable.

Caution!

Do not stare directly at the 2 fiber bore in the SFP transceiver when the switch is in

operation, otherwise the laser may hurt your eyes.

2.3.4 DG-SA-GS4600-EM-2XFP Extended Module Installation

DG-GS4600S series provide 10Gb slots. The procedure for installing the

DG-SA-GS4600-EM-2XFPmodule and the XFP 10Gb fiber transceiver is shown below:

Step 1: Put on an ESD wrist strap (or antistatic gloves).

Step 2: Insert the DG-SA-GS4600-EM-2XFPmodule to the guide rail inside the 10Gb

module slot.

Step 3: Push the DG-SA-GS4600-EM-2XFPmodule along the guide rail gently until it

comes into contact with the machine panel.

Step 4: Insert the XFP transceiver to the guide rail inside the DG-SA-GS4600-EM-2XFP.

Do not put the XFP transceiver up-side-down.

Step 5: Push the XFP transceiver along the guide rail gently until it comes into contact with

the DG-SA-GS4600-EM-2XFP.

Note: the 2XFP extended module does not support hot swappable.

2.3.5 DG-SA-GS4600-EM-2SFP+ extended module Installation

DG-GS4600S series provide 10Gb slots. The procedure for installing the

DG-SA-GS4600-EM-2SFP+ module and the SFP+ 10Gb fiber transceiver is shown below:

Step 1: Put on an ESD wrist strap (or antistatic gloves).

Step 2: Insert the DG-SA-GS4600-EM-2SFP+ module to the guide rail inside the 10Gb

module slot.

Step 3: Push the DG-SA-GS4600-EM-2SFP+ module along the guide rail gently until it

comes into contact with the machine panel.

Step 4: Insert the SFP+ transceiver to the guide rail inside the

DG-SA-GS4600-EM-2SFP+. Do not put the XFP transceiver up-side-down.

Step 5: Push the SFP+ transceiver along the guide rail gently until it comes into contact

«
...
19
20
21
22
23
...
»

Содержание DG-GS4628S


























Отзывы:

Нет отзывов