Digi ConnectPort X4 IA Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 63

background image

- 8 -

PV Temp #1:

Signal

PV Temp #1 Shield: Cable Shield and Drain

Connecting RS-485

The PV

MET

-100-2 is supplied with a half duplex RS-485/422 serial port. The default

firmware build supports RS-422 only. Custom firmware builds are addressable and
support integration into RS-485 networks. Contact RainWise for further information.

Wiring connections are made using the 4-pin screw terminal inside of the PV

MET

-100-2

electronics enclosure. Cable is not supplied with the unit. The RS-485/422 lines are
terminated with a 120 ohm resistor. This can be disabled by moving the termination
jumper, located inside the unit, to the OFF position. This requires removing the enclosure
cover. To do this, remove the 4 screws on the bottom side of the unit.

RS-485/422 Terminals

A (-) :

Negative RS-485

B (+) :

Positive RS-485

Gnd:

Signal Ground

Shield:

Cable Shield and Drain

RS-485 is rated to 4,000 feet (1,200m) at 90 kbps. The RS-485 port on the PV

MET

-100-2

is surge protected but not isolated.

Connecting the Power Supply

The power supply is nominally rated for 24VDC but can accept a voltage in the range of
10 to 30VDC. The inputs are reverse polarity, surge, overvoltage and over current
protected. The power supply is not isolated.

Power Supply Terminals

Earth Gnd:

Earth or Chassis Ground

Gnd:

Negative Supply Voltage

24VDC:

Positive Supply Voltage

Connectivity Verification

Once the station is completely connected, the power supply should be turned on.

When  power  is  applied,  the  red  “Health”  LED  should  start  flashing.  This  LED  is  the
system’s heartbeat and indicates proper functionality. If the “Health” LED is solidly lit or
off, RainWise Inc. should be called for further troubleshooting.

The  TX  and  RX  LEDS  are  used  to  indicate  when  the  station  is  transmitting,  (TX),  or
receiving, (RX), data over the modbus line.

«
...
12
13
14
15
16
...
»

Содержание ConnectPort X4 IA
































































Отзывы:

Нет отзывов

Похожие инструкции для ConnectPort X4 IA

Бренд: B&B Electronics Страницы: 83

Бренд: T-Mobile Страницы: 25

NetVanta 6330 Series

Бренд: ADTRAN Страницы: 4

Бренд: B+B Страницы: 25

Бренд: Ericsson Страницы: 12

Бренд: Technica Engineering Страницы: 7

Бренд: OPW Страницы: 13

Бренд: L&S Страницы: 28

Бренд: Next Level Security Systems Страницы: 10

RouteFinder RF550VPN

Бренд: Multi-Tech Страницы: 76

Бренд: SAE Страницы: 17

RINT8CH Wireless Gateway

Бренд: Rintech Страницы: 2

Бренд: Rosonix Technology Страницы: 16

Бренд: ZyXEL Communications Страницы: 332

Бренд: Rosslare Страницы: 20

Бренд: 24online Страницы: 8

Бренд: Avaya Страницы: 808

Бренд: WAGO Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды