manualshive.com logo in svg

Digi ConnectPort X4 IA, Быстрый старт

Поделиться
Скачать
Digi ConnectPort X4 IA Скачать руководство пользователя страница 11

- 5 - 

Introduction 

The  PV

MET

-100-2  weather  station  is  a  compact  and  economical  solution  designed  to 

monitor the efficiency of photovoltaic installations. It measures ambient air temperature, 
PV panel temperature and either global or plane of array irradiance. The PV

MET

-100-2 is 

Sunspec compliant and uses a 2-wire half duplex serial port for Modbus communication 
to a host.  
 

Unpacking the System 

When unpacking the system the following components should be located. 

 

A1102 – PV

MET

 -100-2 Sensor Assembly 

A2101 – PV Cell Temperature Sensor 
A1020 – Sensor Assembly Mounting Mast 
PV

MET

 -100-2 User’s Guide 

 
If the system was ordered with any accessory, it 
should be located while unpacking the system. The 
available accessories for the PV

MET

 -100-2 are listed 

below. 
 
A2101 – PV Cell Temperature Sensor  
A3000 - Mono-Mount 
A3010 – Tripod Galvanized Steel 
 
If  any  of  the  components  are  missing,  RainWise  Inc. 
should be contacted. 

Installing the Weather Station 

It  is  suggested  that  you  operate  your  system  at  ground  level  and  make  sure  that  all 
components operate properly prior to installation. 
 
If any of the components are damaged or malfunctioning upon receipt, RainWise should 
be contacted. 

Site Requirements and Considerations 

Ambient air temperature and global irradiance can be affected by obstructions and local 
topography.  Each site is different and presents challenges in its own unique way. Any 
object, in excess of 10 degrees above the plane of the irradiance sensor, must not block 
the sensor. The PV

MET

 -100-2 sensor assembly, which contains the ambient air 

temperature, should be no closer than 4 times any obstruction’s height and should be 
placed away from any dark, heat-absorbing surface.  
 
When roof-mounting the sensor assembly, the unit should be mounted toward an edge of 
the roof preferably on the prevailing wind side of the building and should be at least 2 1/2 
feet above the roofline. Avoid locating the station near any heat sources such as chimneys 
or vents.    

 

Содержание ConnectPort X4 IA
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды