manualshive.com logo in svg

Diamond SmartLyte Plus, Руководство по обслуживанию

Поделиться
Скачать
Diamond SmartLyte Plus Скачать руководство пользователя страница 49

1 Introduction

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 49 of 58 

 

1.5.7.       Valve Drivers 

SmartLyte

®

 Plus has 5 solenoid valves for fluid flow control. These solenoids valves (A, B, C, 

V, & R) are controlled from power transistors Q1 to Q5.  To open a solenoid, a pulse of 
voltage 22-24V is applied for 0.5 seconds. Then the voltage drops to 12.5V to hold the 
solenoid open. This feature is applied to conserve energy and prevent overheating the 
valves. 

1.5.8.       Pump Motor Driver 

SmartLyte

®

 Plus has 1 stepper motor for fluid flow. The pump driver circuit provides the 

current and controlling steps for the peristaltic pump. Pump roller with installed tubing 
ensures fluid flows in one direction from pack to waste pump. 

1.5.9.       Input Amplifiers 

IC U24 – U26 Provide high to low input impendence matching for each electrode (Na, K, Cl, 
Ca, & Li) input.  These amplifiers provide a gain of 10 for all incoming signals. 

1.5.10.  Temperature Sensor circuit 

This circuit creates a temperature depended voltage which is converted by software to 
degree C. In SmartLyte

®

 Plus there is no manual adjustment needed.  

1.5.11.  Analog Channel and A/D Converter 

The analog inputs from the amplifiers are connected to IC U23. This IC converts analog 
signal to digital readings that is then used by software for instrument operation. 

1.5.12.  CPU board Connector 

In order to fulfill all responsibilities of the CPU board and the program installed on it, is 
equipped with a number of connectors to interface it with all peripherals. The description of 
the JP connectors is as below: 

JP1 – Power connector 
JP2 – Serial DB9 RS232 connector 
JP3 – Valve board connector 
JP4 – Programmer (MFG Only)  
JP5 – RFID connector 
JP6 – Printer connector  
CN3 – Display flex cable connector 
CN2 – MFG Only 

1.5.13.  Valve Board  

The valve board contains the LED array used to illuminate the measuring chamber and the 
interconnectors used for all solenoids, the peristaltic pump and the door sensor. A ribbon 
cable from the CPU Board supplies the electrical connection for each signal through 
connector JP5. 

Содержание SmartLyte Plus



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды