Diamond SmartLyte Plus Скачать руководство пользователя страница 4

Страница: 4 / 58

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18 Page 4 of 58

Operating Safety Information

• This instrument falls under Safety Category I.

• This instrument is a Class B instrument.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference's, and (2) this device must accept any interference

received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

Note

: This equipment has been checked and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communication. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does not cause harmful interfer

ence to radio or television

reception, which can be determined by turning the equip

ment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures

•

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio TV technician for help

Caution

•

The instrument is designed as a conventional device (closed, not waterproof type).

•

Do not operate the instrument in an explosive environment or in the vicinity of explosive

anesthetic mixtures containing oxygen or nitrous oxide.

•

This instrument is suitable for continuous operation.

•

The power plug is to be plugged into a ground socket only. When using an extension cord, make

sure that it is of the proper size and is properly grounded.

•

Any breakage of the ground lead inside or outside the instrument or a loose ground

connection can cause a hazardous condition when operating the instrument. Intentional

disconnection of the grounding is not permitted.

•

When handling electronic components such as – CPU, RFID PCB, Interface-PC, and printer PCB

– ESD (Electronic Sensitive Device) protection is recommended. ESD mats should be used when

handling and working with these electronic components. ESD packaging is recommended for

transportation.

Содержание SmartLyte Plus



























































Результаты поиска

Содержание SmartLyte Plus

Отзывы:

Бренды по названию

Популярные бренды

Diamond SmartLyte Plus, Руководство по обслуживанию

Результаты поиска

Содержание SmartLyte Plus

Отзывы:

Бренды по названию

Популярные бренды