Diamond GMM/300I Скачать руководство пользователя страница 7

1 - GENERAL INDICATIONS

This appliance is for cooking food in water and

must be used only by professionally qualified

personnel in the way indicated in this instruction

manual.
All other improper uses are dangerous.

1.1 - Instructions for the user

• Read all the information given in this manual carefully as it

gives important indications that ensure the safe and correct

use of the appliance.

• Keep this manual in a safe place for future reference.
• If any repairs are needed always and only contact a technical

assistance centre authorised by the manufacturer and

demand original spare parts.

• Only professionally qualified personnel are allowed to install

the appliance and regulate steam pressure (steam model) or

to convert to another type of gas (gas model) if required.

• To reduce the consumption of energy (gas, steam, electricity

and water) it is advisable not to use the appliance empty for

long periods of time or in conditions that will hinder an

optimum performance (i.e. lid raised, safety valves that keep

venting, etc.).

• The water used for producing steam and cooking food must

be suitable for human consumption and comply with the

following characteristics:

• Total hardness: 0.5 ÷ 5 French degrees
• Concentration of chloride ion (CL-) ~ 10 p.p.m. (parts per

million)

• pH greater than 7
• Electric conductivity: 50 ÷ 2000 µS/cm at 20°.

WARNING!
If water is used with specifications different from

those given here, the guarantee loses all validity.

CAUTION!
Open the lid with caution so as not to get burnt

by the steam or by touching hot parts.

In models with an autoclave lid, the lid must not be lifted until

you are certain there is no pressure inside the pan, pressing

the relief valve vent button “P” (see user instruction sheet)

• The clamps “Q” must be loosened gradually one at a time.
• Daily, when opening the lid, before letting go of  the handgrip

check it stays up; have the balancing springs checked once

every six months by an specialized technician.

• Keep your hands from under the raised lid.

2 - COMMISSIONING

• Before using the appliance, wash the inside thoroughly with

hot water and a suitable detergent and then rinse well.

ATTENTION!
Never start the appliance before having filled

the pan (direct gas mod.) and jacket (electric and

indirect gas models) with water. Failure to

comply with this essential point would seriously

overheat the stainless steel container.

2.1 - Filling the jacket with water 
(indirect gas and electric models)

• Open the maximum level cock “E”.
• Remove the screw plug “G” that closes the jacket spout,

located on the safety unit.

• Pour water through the spout until you see a steady trickle

of water coming through cock “E”.

• Close the cock and put the screw plug “G” back in place.

2.1.1 - Filling the jacket with water (indirect gas

and electric models) with visual level indicator (Z)

• Remove the screw plug “G” that closes the jacket spout,

located on the safety unit.

• Pour water through the spout until the maximum level is

reached, indicated by the visual level indicator (Z)

• Close the cock and put the screw plug “G” back in place.

IMPORTANT

• At the start of each day and with the appliance cold, check

that the water in the jacket has not dropped below the

minimum level.

• This check is carried out by opening the minimum level

control cock “F” from which water should always flow. If this

is not the case, immediately add water up to the maximum

level.

• For those models with the visual indicator in glass, check

(with the appliance cold) each time the appliance is used that

the water is not below the minimum level mark.

2.2 - Filling the tank

• Make sure the big tap “A” is closed.
• Turn the supply pipe “D” to the inside of the tank and open

the two cocks "B" and "C" of the hot or cold water.
The level of the water must be at least 4 cm under the

overflow edge and even lower if there is danger (in the

autoclave models) that the boiling food could clog the safety

valve on the lid.

• Close the lid.
• When closing the autoclave lid, the “Q” clamps must be

tightened gradually and evenly around the pan.

INSTRUCTIONS FOR USE

5

Содержание GMM/300I


























Отзывы: