DiamaPro Systems DX26-P, Руководство пользователя

Страница: 5 / 24

Battery
If not using the machine for an extended period of time, turn off
the battery circuit switch.
Battery replacement
n
Turn off the battery circuit breaker
n
Remove battery from holder
n
Remove the positive & negative terminal connections
n
Remove battery and replace with a DiamaPro Systems recommended
battery
Battery change and maintenance
When replacing the battery on the DX26-P, always remove the battery
from the battery box. When changing the battery, ensure the terminals are
firmly connected to the terminal posts (See Figure 6.6, & Figure 6.7).
When charging the battery, ALWAYS remove and disconnect from the
DX26-P. Failure to do so may cause damage to the machine.
2. MAINTENANCE & REPAIR
Before carrying out the maintenance of the DX26-P make sure
you understand the contents of this manual.
Please contact DiamaPro Systems
®
for further explanations
and information.
• The user shall be required to comply with the qualifications of the
relevant personnel:
OPERATOR / ORDINARY MAINTENANCE TECHNICIAN:
carries out the tasks necessary for the basic functioning
of the machine:
execution of the work cycle, implementation of operator com-
mands, other operations closely linked to normal production, any cleaning
and inspection operation performed on a daily basis, enforcement of ordi-
nary maintenance operations. Works only with enabled safety functions.
MAINTENANCE TECHNICIAN SPECIALIST
(AUTHORIZED DEALER)
Involved in all operating conditions and at all protection levels.
Makes extraordinary operations that cannot be run by the user
Maintenance technicians must possess the skills required by this manual,
as well as the mental and physical requirements necessary and sufficient
to maintain and operate the machine. To ensure the functionality and
durability of the machine daily maintenance must be performed, carrying
out operations in compliance with the safety requirements.
Only the authorized dealer can make adjustments and operations that are
not assigned to the operator. It is forbidden to make adjustments and in-
terventions during machine operation. Before performing any maintenance
operation disconnect the machine from the power sources and wait for the
cooling of the hot parts (engine, spark-plug area, air filter area, etc.)
n
Disengage the Clutch
n
Bring the accelerator at idle speed.
n
Close the propane tank valve.
n
Stop the engine (position the ignition key to OFF).
n
Turn battery switch to the off position
n
Carry out maintenance operations with the machine stopped.
n
Allow machine to properly cool off
Before performing maintenance:
n
Thoroughly clean the DX26-P. If in doubt about how to perform occa-
sional repairs, contact our Technical Support or an authorized dealer.
n
Upon finishing the job perform a thorough cleaning from processing
residues.
Good maintenance requires constant and methodical control of all parts of
the machine and adaptation of tests to its actual usage. Periodic inspec-
tions are crucial to keep the machine efficient and reduce repairs and any
resulting dangers.
We recommend that you have your DX26-P serviced by an authorized
dealer or a DiamaPro Systems
®
technician every 500 hours.
Note: frequency is taken over considering a working day of 8 hours.
Replacement of the clutch belt
If, as a result of a visual inspection, it appears that the belts are
worn or cracked, replace them, operating as follow:
n
Allow motor to cool before replacing belts
n
Remove side plate located on opposite side from the battery shut off
n
Loosen the six bolts on the motor mount plate
n
Loosen the belt tension screw on the front under the exhaust to relive
tension to remove belt
n
Remove belt under the clutch and over the gearbox pulley
n
Install new belt the same way, over the gearbox pulley and under the
clutch
n
Set tension back with tension bolt
n
Tighten 6 side bolts on motor mount plate
n
Reinstall side plate
2.1 SCHEDULED MAINTENANCE
2.2 ROUTINE & ADDITIONAL MAINTENANCE
IMPORTANT!
TO AVOID DAMAGE TO THE MACHINE
STRICTLY follow the engine manufacturer’s recommended oil in
the manual provided with the machine. 10W-40 is recommended.
NOTE
Although 10W-40 engine oil is the recommended oil for most conditions,
the oil viscosity may need to be changed to accommodate atmospheric
conditions. Please contact the authorized dealer if running machine in
extreme conditions for the correct oil choice.
IMPORTANT!
Always remove the battery for charging.
Only recharge the battery in a dry environment. Protect the contacts
from dirt and moisture stagnation. Don’t spray with water.
CAUTION
!
ALWAYS REPLACE TERMINAL COVERS OVER THE
TERMINALS OF THE BATTERY (Figure 6.8)
Engine oil filling
Refer to the engine manual and the MAINTENANCE CHAPTER
OF THIS PUBLICATION. The oil filling must be performed with
the machine off after hot parts have cooled.
n
Remove oil fill cap
n
Remove valve lock and set aside
n
Lower oil drain tube into an oil containment vessel and remove cap
n
Unlock valve and let oil drain
n
Once oil has drained, remove oil filter
n
Install new oil filter, place fresh oil around filter seal before installing
n
Close valve & replace lock
n
Add oil. Check level on dipstick.
n
Tighten oil fill cap
n
Check for any leaks
Oil Viscosity
Choose the viscosity according to the temperature as follows: