DiamaPro Systems DX26-P, Руководство пользователя

Страница: 4 / 24

Form a habit of checking to see that tools such as adjusting wrenches are
removed from the machine and properly stored before starting.
Watch what you are doing. Use common sense. Do not operate machine
when you are tired or fatigued.
Do not operate machine while under the influence of drugs, alcohol, or
any medication.
Do not operate machine with missing or improperly mounted parts.
Verify all machine guards are in good condition and will function properly
before using the machine. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other conditions that
may affect machine operation. A guard, power switch or other part that is
damaged should be properly repaired or replaced by an authorized
service center.
Never touch moving parts such as blades, belts, and others.
Stop using machine immediately if any abnormalities are observed during
operation. Examples of abnormalities include unusual noise and vibration
When replacing a component part with a new one, use only the same type
and quality of the previous part. Never attempt to repair a machine if you
are unfamiliar with proper procedures and techniques required.
Refer to this operations and maintenance manual as well as any additional
instructions included from other manufacturers.
1.23 REMOVE ADJUSTING TOOLS
1.24 STAY ALERT
1.25 DO NOT USE DRUGS, ALCOHOL,
MEDICATION
1.26 KEEP ALL PARTS IN CORRECT POSITION
1.27 CHECK DAMAGED PARTS
1.29 STOP OPERATION IMMEDIATELY IF ANY
ABNORMALITY IS DETECTED
1.28 NEVER TOUCH MOVING PARTS
1.30 WHEN REPLACING A PART, USE THE SAME
TYPE AND QUALITY
1.31 SAVE THESE INSTRUCTIONS
CALIFORNIA PROP 65 WARNING
Thank you for purchasing a DIAMAPRO SYSTEMS
®
product. This manual
provides information and procedures to safely operate and maintain the
DiamaPro DX26-P. For your own safety and protection from injury, carefully
read, understand, and observe the safety instructions described in this
manual. Keep this manual or a copy of it with the machine. If you lose this
manual or need an additional copy, please contact DiamaPro Systems
®
.
This machine is designed and built with user safety in mind; however, it
can present hazards if improperly operated and serviced.
Please follow the operating instructions carefully. If there are any questions
regarding operating or servicing of this machine, please contact
DiamaPro Systems
®
.
DUST WARNING
Cutting, especially when DRY cutting, generates dust that
comes from the material being cut, which frequently contains
silica.
When dry cutting, be sure to use a HEPA filtered dust collector.
Silica is a basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Exposure to excessive amount
of such dust can cause:
n
Respiratory diseases (affecting your ability to breath), including
chronic bronchitis, silicosis and pulmonary fibrosis from exposure
to silica. These diseases may be fatal;
n
Skin irritation and rash; and
n
Cancer according to NTP* and IARC*
*National Toxicology Program, International Agency for Research
on Cancer
Take precautionary steps
n
Avoid inhalation of and skin contact with dust, mist and fumes;
n
Wet cut when feasible, to minimize dust;
n
Wear and ensure that all bystanders wear appropriate respiratory
protection such as dust masks designed to filter out microscopic
particles. (See OSHA 29 CFR Part 1910.1200)
Use of this product can cause exposure to materials known to the
State of California to cause
cancer and/or birth defects or other reproductive harm.
CALIFORNIA PROP 65 WARNING
CAUTION
Respirable crystalline silica. May cause cancer.
Causes damage to lungs.
Wear respiratory protection during exposure.
Use appropriate dust control equipment to keep
dust within OSHA and local regulation limits.
!
WARNING & ATTENTION
WARNINGS
n
Please check the fastening of each component of the propane gas
system before use, tighten loose fasteners, and check whether there is
leakage at the gas cylinder, pipeline, and connection, and do not oper-
ate the equipment and repair if there I any leakage
n
Proper selection of propane fuel or poor fuel quality will cause engine
failure and affect the normal operation of the engine.
n
Do not use tools or other metal objects to contact the two terminals of
the battery, and do not short-circuit the positive and negative terminals
of the battery, as there is a danger of explosion. The connection of
battery terminals should be firm. When the terminal is loose, there is a
danger of explosion when a spark occurs due to poor contact. Damaged
cables and wires can cause e fire. Check and replace before
reconnecting.
ATTENTION
n
Avoid splashing water on the engine and control box during machine
cleaning
n
Never do maintenance on any part of the fuel system while the engine is
running
n
If the machine does not appear to be operating properly, it should be
shut down.
n
Ensure that the tools are installed in place and securely