Diamant F60000, Инструкция по эксплуатации и перечень запасных частей

Страница: 24 / 52

24
WARNING: Before performing any
maintenance, ALWAYS locate the machine on
a level surface with the engine / motor OFF,
and the start switch in the OFF position, and
the power source disconnected.
Check Daily:
1)
All Models :
a) At the end of each day clean the machine to
remove sludge buildup.
2)
Gasoline Model:
a) Check engine air cleaner daily! If cutting
dry check engine air cleaner every four
hours! Clean or replace air cleaner
element as recommended by the engine
manufacturer.
b) Check engine oil daily. Change engine oil
after every 50 hours of operation. Engine
Oil capacity is See engine operation
manual for proper care and maintenance.
Every 50 Hours:
1) All Models:
a) Lubrication Points:
Lubricate every 50 hours using only a
Premium Lithium 12 based grease
conforming to NLG1 GRADE #2
consistency.
1) Spindle Bearings : Six places total, three
Bearings [RR 1] on top of the gearbox
[FIG. 29] and three below the gearbox
(Not Shown).
2) Rear Wheels: Two places [FIG. 30].
2) Gasoline Model:
Change Engine Oil: Change engine
oil after every 50 hours of operation.
Engine Oil Type
Under normal operating conditions use SAE 10W30
API service classification SF or SG. See engine
operation manual for other recommended oil types.
Engine Oil Capacity (Honda GXV340)
1.16 U.S. Quarts 1.1 Liters
a) Engine Oil Change Procedure:
1. Drain the oil while the engine is still warm to
assure rapid and complete oil drain. Pivot the
Rear Axle To The
Operation Position [F] .
Place a bucket under the Oil Drain Hose
[WW] , [FIG. 12, FIG. 13] to catch the used oil.
Remove the oil drain plug on the end of the Oil
Drain Hose [WW] and wait for all of the used
oil to be drained for the engine.
2. Re-install and securely tighten the plug in the
end of the Oil Drain Hose [WW] .
3. Re-fill engine with the recommended oil type.
See the engine operation manual for the oil fill
location and proper oil level. Note that the
required oil capacity will be slightly larger
because of the volume of oil contained in the
Oil Drain Hose [WW] .
4. Check the oil level. If the proper oil level is
indicated, re-install the oil fill cap.
5. Dispose of the used oil in a proper container
and in a manner that is compatible with the
environment.
When Required:
1) All Models:
a) Lubrication:
Gearbox Grease Port [RR 3] [See FIG.
29]
: Used to lubricate the transmission
gears, if required. These gears are factory
lubricated with 24 ounces (.68 kg) of
Lubriplate (Brand) 630-2 or equal, and
should not require any lubrication until
service work to the gears is required (at
500 – 1000 hours). Lubricate as required
with Lubriplate (Brand) 630-2 or equal. To
inspect the inside of the gearbox, remove
the two Capscrews that attach the
Gearbox Grease Port Cover [RR 3] and
remove the cover. A 1.00” (25 mm) hole
in the gearbox allows visual inspection of
the condition and quantity of the grease
and the gears.
Note: Early models have one removable
Capscrew that exposes a .50” (12 mm)
diameter inspection hole.
b) Replace Accessory Disk Isolators: Each of
the Accessory Disks [P] have six (6)
rubber isolators (See Parts List – Gearbox
Assembly) that constantly flex and move
as the machine operates. Over time the
isolators can deteriorate and wear out.
Check to see if they are damaged or
deteriorated, if so, replace immediately.
All twelve (12) isolators should be
replaced as a set.
c) V-Belt Inspection: Check to see that the V-
belts are not frayed or worn. If they are,
replace immediately.
8. V-Belt Tension
All Models:
Check V-Belt tension when unit is new and never set
belt tension beyond this point.
The machine is equipped with high tension V-Belts.
The belts are properly tensioned at the factory, but
after a few hours of operation they will stretch and
become loose.