manualshive.com logo in svg

Diagraph I.V./700, Руководство по обслуживанию

Поделиться
Скачать
Diagraph I.V./700 Скачать руководство пользователя страница 40

5750-212

Revision  A

Page 40

The second line of the LCD will prompt for "Dot Adjustment." If this dot is small in the sample print (see

the first sample below), increase the value by 10 which increases the size of the dot for the first print.
If the dot was full-size, DO NOT enter a new value: leave the existing value and press ENTER

8 The display will change to "1st Dot Adjust:2" for the second valve. Press ENTER and the second line will

prompt for "Dot Adjustment." Repeat this process through all seven dots.

9 After the seventh dot, press SET-UP.  The LCD will prompt for "Factory Setting."  Select "2-YES."

Wait the time designated in step 5, then print a message. If the print is satisfactory, unplug and replug to
set the I.V./700 in print mode.  If the print is unsatisfactory reset the first dot by repeating this procedure
(C8) and run another sample.  Repeat until you achieve a satisfactory first print.

Noticeable size differences between dots printed in rows (Ö) and dots printed in columns (×)

Dots with column adjustment

set too low

Nominal Letters

Dots with column adjustment

set too high

Column Dot Adjustment

When the I.V./700 prints a single dot, the printing
channel has individual access to ink pressure.
When all seven channels print simultaneously, they
share the ink pressure.  This sharing can produce
printed dots in columns that are slightly smaller in
diameter than single printed dots.  The column dot
adjustment enables you to eliminate slight size
variances between dots printed in rows and dots
printed in columns.  Start by unplugging the I.V./
700.
1 Press and hold ALT and INFORMATION.
2 Plug in the barrel connector.
3 Release the keys when the LCD shows "Informa-

tion."

  Information
  1-Unused Messages

4 Press SET-UP
5 Press I on the QWERTY keypad.  The LCD will

prompt for a change in value of the column dot
adjustment:

  Column Dot Adjust:
  3

6 Scroll to a higher or lower number.
7 Press ENTER.
8 Run a print sample at the speed of a production

run.

9 Continue adjusting until the dots in columns match

the size of dots printed in rows.

Содержание I.V./700



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды