DFI PIC-H110 Скачать руководство пользователя

Страница: 21 / 24

www.d

.com

Chapter 2 Hardware Installation

Chapter 2

DVI-D Connector (optional)

DVI-D

KB/MS Connector

KB/MS

The Keyboard/Mouse connector is used to connect PS/2 keyboard and PS/2 mouse by means

of a PS/2 cable.

Connecting the PS/2 Cable

The system board package comes with a PS/2 cable. Connect one end of the cable to the KB/

Mouse connector. The other ends are used to connect a PS/2 keyboard and a PS/2 mouse.

1 2

KBCLK

GND

KBDATA

KBMS POWER

MSCLK

MSDATA

GND

KBMS POWER

PS/2 keyboard port

PS/2 mouse port

Connect to the

board’s KB/Mouse

connector

Wake-On-PS/2 Keyboard/Mouse

The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2

mouse to power-on the system.

The DVI-D connector is used to connect a digital LCD monitor or LCD TV. Connect the display

device’s cable to the connector.

BIOS Setting

Configure the display devices in the Advanced menu (“Video Configuration” submenu) of the

BIOS. Refer to the chapter 3 for more information.

Driver Installation

Install the graphics driver. Refer to the chapter 4 for more information.

Содержание PIC-H110

























Результаты поиска

Содержание PIC-H110

Отзывы:

Похожие инструкции для PIC-H110

Бренды по названию

Популярные бренды

DFI PIC-H110, Руководство пользователя

Результаты поиска

Содержание PIC-H110

Отзывы:

Похожие инструкции для PIC-H110

Бренды по названию

Популярные бренды