Analog Devices AD9910 User Manual Download

Page: 1 / 17

Evaluation Board User Guide

UG-207

One

Technology

Way

•

P.O.

Box

9106

•

Norwood,

02062-9106,

U.S.A.

•

Tel:

781.329.4700

•

Fax:

781.461.3113

•

www.analog.com

Evaluation Board for 1 GSPS DDS with 14-Bit DAC

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.

Rev. A | Page 1 of 16

FEATURES

Full-featured evaluation board for the AD9910
PC evaluation software for control and measurement of the

AD9910

USB interface
Graphic user interface (GUI) software with frequency sweep

capability for board control and data analysis

Factory tested and ready to use

PACKAGE CONTENTS

AD9910 evaluation board
AD9910/PCBZ installation software CD
USB cable

GENERAL DESCRIPTION

This user guide describes how to set up and use the AD9910
evaluation board. The AD9910 is a 1 GSPS DDS with a
14-bit DAC.

The evaluation board software provides a graphical user interface
(GUI) for easy communication with the device along with many
user-friendly features such as the mouse-over effect.

This user guide is intended for use in conjunction with the

AD9910

data sheet, which is available from Analog Devices,

Inc., at

www.analog.com

EVALUATION BOARD BLOCK DIAGRAM

USB

INTERFACE

DC POWER

HEADER

REFERENCE

CLOCK

PARALLEL

DATA
PORT

SPI

DAC OUT

AD9910

TO PC

MULTICHIP

SYNC

Figure 1.

Summary of Contents for AD9910


















Search results

Summary of Contents for AD9910

Reviews:

Related manuals for AD9910

Brands by name

Popular brands

Analog Devices AD9910, User Manual

Search results

Summary of Contents for AD9910

Reviews:

Related manuals for AD9910

Brands by name

Popular brands