DFI KU171 Скачать руководство пользователя

Страница: 18 / 65

www.dfi .com

Chapter 2 Hardware Installation

Chapter 2

USB Ports

The USB device allows data exchange between your computer and a wide range of simultane-

ously accessible external Plug and Play peripherals.

The system board is equipped with four onboard USB 3.0 ports (USB 1-2/3-4). The 10-pin

connectors allow you to connect 4 additional USB 2.0 ports (USB 6-7/8-9). The additional USB

ports may be mounted on a card-edge bracket. Install the card-edge bracket to an available

slot at the rear of the system chassis and then insert the USB port cables to a connector.

BIOS Setting

Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the

BIOS. Refer to chapter 3 for more information.

Driver Installation

You may need to install the proper drivers in your operating system to use the USB device.

Refer to your operating system’s manual or documentation for more information.

Wake-On-USB Keyboard/Mouse

The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse

to wake up a system from the S3 (STR - Suspend To RAM) state.

USB 3.0

USB 4

USB 2

USB 1

USB 3

VCC

-Data +Data GND

VCC

-Data +Data GND

USB 2.0

USB 8-9

USB 6-7

USB 3.0

Содержание KU171


































































Результаты поиска

Содержание KU171

Отзывы:

Похожие инструкции для KU171

Бренды по названию

Популярные бренды

DFI KU171, Руководство пользователя

Результаты поиска

Содержание KU171

Отзывы:

Похожие инструкции для KU171

Бренды по названию

Популярные бренды