DFI KU171 Скачать руководство пользователя

Страница: 19 / 65

www.dfi .com

Chapter 2 Hardware Installation

Chapter 2

Audio

Rear Audio

The system board is equipped with 2 audio jacks. A jack is a one-hole connecting interface for

inserting a plug.

• Line-out Jack (Lime)

This jack is used to connect a headphone or external speakers.

• Mic-in

(Pink)

This jack is used to connect an external microphone.

BIOS Setting

Configure the onboard audio devices in the Advanced menu (“Audio Configuration” submenu)

of the BIOS. Refer to chapter 3 for more information.

Driver Installation

Install the audio driver. Refer to the chapter 4 for more information.

Line-out Mic-in

I/O Connectors

Digital I/O Connector

Digital I/O Power Connector

The 8-bit Digital I/O connector provides powering-on function to external devices that are con-

nected to the connector.

Digital I/O Connector

Pins

Function

DIO0

DIO1

DIO2

DIO3

DIO4

DIO5

DIO6

DIO7

Line-out

Mic-in

Digital I/O

+12V

Ground

5VSB

Digital I/O Power

Содержание KU171


































































Результаты поиска

Содержание KU171

Отзывы:

Похожие инструкции для KU171

Бренды по названию

Популярные бренды

DFI KU171, Руководство пользователя

Результаты поиска

Содержание KU171

Отзывы:

Похожие инструкции для KU171

Бренды по названию

Популярные бренды