DFI KU171 Скачать руководство пользователя

Страница: 22 / 65

www.dfi .com

Chapter 2 Hardware Installation

Chapter 2

Front Panel Connector

HD-LED - Hard Drive LED

This LED will light when the hard drive is being accessed.

RESET - Reset Switch

This switch allows you to reboot without having to power off the system.

PWR-LED - Power/Standby LED

When the system’s power is on, this LED will light. When the system is in the S1 (POS - Power

On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend To

RAM) state, it will blink every 4 seconds.

ATX-SW - Power Switch

This switch is used to power on or off the system.

Pin Pin Assignment

N.C.

PWR-LED

3V3SB

HD-LED

3V3

3V3SB

HD_LED

Power_LED

RESET

Ground

ATX-SW

Ground

RST Signal

Power_Button

11 N.C.

HD-LED

RESET

PWR-LED

ATX-SW

Cooling Fan Connectors

The fan connectors are used to connect cooling fans. The cooling fans will provide adequate

airflow throughout the chassis to prevent overheating the CPU and system board components.

BIOS Setting

The Advanced menu (“SIO NUVOTON6106D” submenu) of the BIOS will display the current

speed of the cooling fans. Refer to chapter 3 for more information.

Front

Panel

Sense

Power

Ground

CPU Fan

System Fan 2

System Fan 1

Sense

Power

Ground

Sense

Power

Ground

Содержание KU171


































































Результаты поиска

Содержание KU171

Отзывы:

Похожие инструкции для KU171

Бренды по названию

Популярные бренды

DFI KU171, Руководство пользователя

Результаты поиска

Содержание KU171

Отзывы:

Похожие инструкции для KU171

Бренды по названию

Популярные бренды