DFI AL051 Скачать руководство пользователя

Страница: 28 / 43

www.dfi.com

Chapter 3 BIOS Setup

Chapter 3

www.dfi.com

Chapter 3 BIOS Setup

Audio Configuration

This section is used to configure the audio settings.

Audio Controller

Control the support of the high-definition audio device.

Disabled

HD Audio will be disabled.

Enabled

HD Audio will be enabled.

Audio Controller

Advanced

Help

↑/↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←/→

Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Enable/Disable HD-Audio

Support

Rev. 5.0

SATA Configuration

This section configures the SATA controller.

SATA Controller

This field is used to enable or disable the Serial ATA controller.

SATA Mode Selection

The mode selection determines how the SATA controller(s) operates.

AHCI Mode

This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Inter-

face).

SATA Speed Selection

Select Serial ATA controller(s) speed from Gen1 (1.5 Gbit/s), Gen2 (3.0 Gbit/s) or Gen

3 (6.0 Gbit/s).

Serial ATA Port 0/1 and Hot Plug

These fields are used to enable or disable the serial ATA ports and their hot plug func-

tion.

Enables or Disables the

Chipset SATA Controller.

SATA Controller

SATA Mode Selection

SATA Speed

Selection

SATA Port 0

Hot Plug

SATA Port 1

Hot Plug

Advanced

Help

↑/↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←/→

Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Rev. 5.0

<AHCI>

<Gen3>

[Not Installed]

[Not Installed]

Содержание AL051












































Результаты поиска

Содержание AL051

Отзывы:

Похожие инструкции для AL051

Бренды по названию

Популярные бренды

DFI AL051, Руководство пользователя

Результаты поиска

Содержание AL051

Отзывы:

Похожие инструкции для AL051

Бренды по названию

Популярные бренды