DEXAPLAN DV 622, Руководство пользователя

Страница: 5 / 22

Page 5
6. Safety instructions
The following instructions are provided for your safety
and satisfaction during operation of the device. Note that
non-observance of these safety instructions results in
significant risks of accident.
Danger!
! Do not leave small children unsupervised with the
device, packaging material or small parts. Otherwise
there is a risk of fatal injury due to choking or
suffocation.
! Do not damage any gas, electricity, water or
telecommunication lines during drilling and fixing
work. Otherwise there are dangers of fire, personal
and fatal injury.
! Treat the cables carefully. Lay these so that they
cannot be damaged and do not present any tripping
hazard. Otherwise there are dangers of fire, personal
and fatal injury.
! If you use the device for monitoring babies or small
children ensure that the camera and cable are out of
reach of children. Otherwise there is a risk to life and
limb!
! Do not pull the cables over sharp edges and do not
crush or crimp them elsewhere. Otherwise there are
dangers of fire, personal and fatal injury.
! Prevent the event recorder and the power supply from
coming into contact with moisture and do not
submerge the equipment in water. Otherwise there is
a danger of fatal injury.
! Only operate the device with 5 V DC from the supplied
power supply. Use a mains socket near to the device
and keep this accessable. The mains current must
comply with 230 V, 50 Hz and the plug must be fitted
with a fuse acoording to regulations. Otherwise there
are dangers of fire and fatal injury.
Attention! Non-observance of these instructions
puts property at risk of damage.
! Protect the equipment and the cables against strong
magnetic or electrical fields and against strong
mechanical loads and vibrations.
! Do not place the equipment near fire, heat or in areas
of high temperature.
! Only use the equipment with the supplied original
parts or original accessories.
! Do not connect any damaged device (e.g. damage in
transit). Repairs to the equipment must only be
performed by specialists.
! Always switch off the ON / OFF switch before
inserting or removing the SD memory card. Never
remove the SD memory card from the device or
switch the device off while recording. Otherwise there
is a risk of damage to the card and loss of the stored
data.
7. Location of the event recorder
Observe the following points:
! Place the device on a level surface.
! Pay attention to the space required for the plug
connections to the event recorder.
! If you want to observe live images, place the event
recorder near the TV or the video monitor.
! When choosing the location of the recorder consider
the cable lengths for the TV or video monitor, for the
mains power socket and for the camera.
8. Location of the camera
Observe the following points:
! Position the camera so that no direct light or sunshine
falls on the lens opening. Remember that the position
of the sun changes. Check the camera image before
mounting. Provisionally connect and commission the
device and hold the camera in the desired position. If
necessary, change the camera position until you have
found the desired view.
! The camera has infrared illumination for the close
range. You can improve the quality of the image at
night by using additional illumination. The camera
automatically switches to black and white in low light
conditions.
! If you want to install the camera outdoors, then ensure
there is a suitable possible cable routing at the
installation location.
! Protect the camera against direct rainfall if possible.
9. Connection
! Remove the equipment and the accessories from the
packaging.
! Peel off the protective film from the rear side of the
event recorder.
Connect the components as follows (see Fig. C):
! Connect the plug of the camera [23] to the socket
[24c] of the connection cable. Press the connector
into the socket until you hear it click in place.
! Connect the yellow plug [24a] of the connecting cable
to the camera input CH1 [15] of the event recorder.
! Connect the black power supply socket [24b] of the
connecting cable to the plug [22a or 22b] of the low
voltage distribution cable.
!
Connect the power supply socket [22c] of the low
voltage distribution cable to the cable connector of the
power supply [19].
! Connect the plug [22d] of the low voltage distribution
cable to the power supply connection [17] of the event
recorder.
! Connect one of the plugs of the video output cable
[20] to the video output [16] of the event recorder.
GB / IE - 5