DeWalt DW714 B5, Оригинальное руководство пользователя

Страница: 21 / 40

ENGLISH
19
Lubrication
Closed-type, grease-sealed ball bearings are used throughout. These
bearings have sufficient lubrication packed in them at the factory to last
the life of the mitre saw.
Cleaning
Before use, carefully check the upper blade guard, movable lower
blade guard as well as the dust extraction tube to determine that it will
operate properly. Ensure that chips, dust or workpiece particle cannot
lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow the
instructions given in section Mounting the Saw Blade . Remove the
jammed parts and reassembling the saw blade.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: To reduce the risk of injury,
regularly clean
the table top.
WARNING: To reduce the risk of injury, regularly clean
the dust collection system.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
e
WALT , have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
e
WALT , recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked with
this symbol must not be disposed of with normal household
waste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle electrical
products and batteries according to local provisions. Further information
is available at www.2helpU.com .tacts are available on the Internet at:
www.2helpU.com .
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE! WHAT’S WRONG? WHAT TO DO
Saw will not
start
1. Saw not plugged
in
1. Plug in saw.
2. Fuse blown or
circuit breaker
tripped
2. Replace fuse or reset
circuit breaker.
3. Cord damaged 3. Have cord replaced by
an authorised service
agent.
4. Brushes worn
out
4. Have brushes replaced
by an authorised service
agent or replace them
yourself. Refer to
Brushes.
Saw makes
unsatisfactory
cuts
1. Dull blade 1. Replace blade. Refer
to Mounting the Saw
Blade.
2. Blade mounted
backwards
2. Turn blade around.
Refer to Mounting the
Saw Blade.
3. Gum or pitch on
blade
3. Remove blade and
clean with turpentine
and coarse steel wool
or household oven
cleaner.
4. Incorrect blade
for work being
done
4. Change the blade type.
Cutting wood use wood
blade, cutting aluminum
use aluminum blade
.
Blade does
not come up
to speed
1. Extension cord
too light or too
long
1. Replace with adequate
size cord.
2. Low house
current
2. Contact your electric
company.
Machine
vibrates
excessively
1. Saw not
mounted
securely to stand
or work bench
1. Tighten all mounting
hardware. Refer to
Bench Mounting.
2. Stand or bench
on uneven floor
2. Reposition on flat level
surface.
3. Damaged saw
blade
3. Replace blade. Refer
to Mounting the Saw
Blade.
Does not
make accurate
mitre cuts
1. Mitre scale
not adjusted
correctly
1. Check and adjust. Refer
to Adjustments.
2. Blade is not
square to fence
2. Check and adjust. Refer
to Adjustments.
3. Blade is not
perpendicular to
table
3. Check and adjust fence.
Refer to Adjustments.
4. Workpiece
moving
4. Use the vertical or
horizontal clamp to
clamp workpiece
securely.
Material
pinches blade
1. Cutting bowed
material
1. Refer to Bowed
Material under Special
Cuts.